IR7200 replace laser assembly

[madu132]

I want to replace laser assembly on IR7200.
In SM, it said to adjust the LA-DELAY after replacement.

Where can I found this LA-DELAY code in laser assembly unit? I replace it with used laser assembly so it will have no box or any doc.

thanks before.

[charm5496]

Re: IR7200 replace laser assembly

I want to replace laser assembly on IR7200.
In SM, it said to adjust the LA-DELAY after replacement.

Where can I found this LA-DELAY code in laser assembly unit? I replace it with used laser assembly so it will have no box or any doc.

thanks before.

I have swapped dozens of these laser units from used machines and have never went through that adjustment procedure before. Are you sure that the laser you are putting was good before installing it?

[zoraldinho]

Re: IR7200 replace laser assembly

If you have replaced the laser unit, enter the value indicated on the
label attached to the laser unit from 0 to 4807


Also work without this settings like Charm say.

[madu132]

Re: IR7200 replace laser assembly

I have swapped dozens of these laser units from used machines and have never went through that adjustment procedure before. Are you sure that the laser you are putting was good before installing it?

ok, thanks for clarify Charm, I will try it.

If you have replaced the laser unit, enter the value indicated on the
label attached to the laser unit from 0 to 4807

Also work without this settings like Charm say.

Zoraldinho, can you make it more clearly which label is it? there are 3 labels on the assembly. 2 of them have more than 4 digit number, there is one have marking *D333*, is this what you mention ?

thank you

[teckat]

Re: IR7200 replace laser assembly


Go for it/ usually adjusts it self/ as said by others


COPIER>ADJUST>LASER>LA-DELAY
0 to 4807
Use it to adjust the delay line of pixels so that laser A and laser B may be
coordinated in main scanning direction.
If you have replaced the laser unit, enter the value indicated on the
label attached to the laser unit.

LA-PWR-A
Use it to enter the power adjustment value for laser A.
Range of adjustment 0 to 255
If you have replaced the laser unit, enter the power adjustment value
for laser A indicated on the unit.

LA-PWR-B
Use it to enter the power adjustment value for laser B.
Range of adjustment 0 to 255
If you have replaced the laser unit, enter the power adjustment value
for laser B indicated on the unit.


DLY-FINEChecking for a Laser Delay
Use a magnifying glass to make sure that the distance between
a and b in the figure is a specific distance; otherwise, try changing the setting under COPIER>ADJUST>LASER>DLY-FINE.

Spy glass.jpg

laser.JPG

[stosh]

Re: IR7200 replace laser assembly

Does anybody have a suggestion on where to buy a refurb' laser unit online? Long story but a 7095 was dropped in my lap but the catch is the laser unit is missing so I'm looking to buy a replacement unit to get the machine up and running.

Thanks

[charm5496]

Re: IR7200 replace laser assembly

In the US you have NWRS or Hytec to order them from.

[teckat]

Re: IR7200 replace laser assembly

Does anybody have a suggestion on where to buy a refurb' laser unit online? Long story but a 7095 was dropped in my lap but the catch is the laser unit is missing so I'm looking to buy a replacement unit to get the machine up and running.

Thanks

Warning---- do not buy a FM2-5449-000/FM2-5449-010 unless it was repaired for the defective Laser Diodes /E110/Low Density/& Mirror Image==== ask for paper work

only Nation-Wide Repair Service, Inc. & HYTEC did the repairs for Canon


Cost is about 800.00/ 1,700.00 US

imageRUNNER 7105 / 7095 / 7086

Laser Scanner Assembly is FM2-5449-010

CAL 866.655.8676---Nation-Wide Repair Service, Inc.
Circuit Board Repair, Canon, Ricoh, Savin, Lanier Gestetner, Konica, Kyocera Mita - Nation-Wide Repair Service, Inc. (NWRS)


Factory Authorized Circuit Board Repair by Hytec Dealer Services, Inc.

800.883.1001 - 407.297.1001

[stosh]

Re: IR7200 replace laser assembly

Warning---- do not buy a FM2-5449-000/FM2-5449-010 unless it was repaired for the defective Laser Diodes /E110/Low Density/& Mirror Image==== ask for paper work

only Nation-Wide Repair Service, Inc. & HYTEC did the repairs for Canon


Cost is about 800.00/ 1,700.00 US

imageRUNNER 7105 / 7095 / 7086

Laser Scanner Assembly is FM2-5449-010

CAL 866.655.8676---Nation-Wide Repair Service, Inc.
Circuit Board Repair, Canon, Ricoh, Savin, Lanier Gestetner, Konica, Kyocera Mita - Nation-Wide Repair Service, Inc. (NWRS)


Factory Authorized Circuit Board Repair by Hytec Dealer Services, Inc.

800.883.1001 - 407.297.1001

Great information thank you! I spoke with NWRS and they have it. Thank you everybody for the help!!!!!

[charm5496]

Re: IR7200 replace laser assembly

Awesome!!!