"Load Paper" When trying to print #10 envelopes from MS Word on C2230

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

Definately a driver issue. Installed the C5235 driver and printed envelope perfectly. Thanks.

[Canuck]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

My last input..make sure there is not a conflict between machine and Word if machine is set to run envelopes at plain speed(to avoid creases). Shouldn't cause an issue but....also if it will print other orientation but image is out 90 degrees....fix it in WORD....WORD. Good luck

[Canuck]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

You are not using the Canon irac2230 driver? Install it.The clbp is just to run a stupid little printer and this is also an advanced box. The core of the driver is similar but the 2230 has features that the other doesnt.There are differences. Install the proper driver then go from there. This should have been step 1 to eliminate the possibility. If it still doesn't work....WORD,WORD,WORD,WORD....something is not set right. I have tons of customers that print COM10 envelopes on these machines all the time.What version of Word? Don't blame the machine. I've been down this path..............personally i'm done with this thread...lol

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

This is a fairly new model. With all the experts here somebody must have a legitimate explanation.

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

This has to be a Word-Canon compatibility issue. What strikes me as odd though is that the custom paper size option on the machine specifies a minimum short side (x) as 5.5" when set vertically in the MP tray, yet the machine is supposed to accept COM10 which has a short side of 4.13". Why can you only specify a 5.5" short side minimum entering a custom size? The only way to mimic the COM10 size using the custom size feature is by swapping the short and long side values and feeding the envelope horizontally which is not recommended unless the optional inner finisher is installed.

Doesn't this inconsistency seem odd? If the custom size short side minimum is greater that the COM10 short size then why would the machine accept COM10 at all through the MP tray? My guess is the machine doesn't take the size when set vertically in the MP tray despite suggesting it. However, the machine does accept the COM10 vertically through the MP tray using the copy function. I did not check to see if the custom size minimum values are different when copying.

This is just a very odd anomaly. It's very frustrating when you have a high end machine that can't accommodate a common paper size. I have to print the COM10 envelopes in the LBP7780Cdn when I should be able to print them in the C2230 as well. It's the same driver for goodness sake!

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

--------------------------

there was a LOAD PAPER message issue on the C2000 series with Multi-Purpose tray Printing on A4R/LTRR detection/ was fixed in a Firmware update/

don't see anything for C2230 v32.04.01/

will keep looking

You think it's a problem with the UFR driver? Very strange that is feeds the COM if you do a copy but not for print. I hope Canon is aware of this issue.

[teckat]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

great thank you.

--------------------------

there was a LOAD PAPER message issue on the C2000 series with Multi-Purpose tray Printing on A4R/LTRR detection/ was fixed in a Firmware update/

don't see anything for C2230 v32.04.01/

will keep looking

[teckat]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

great thank you.

------------------------------------------------
Just found out

It looks like on this series C2230/C2225 Printer model , Canon has eliminated the paper width VR adjustment for it's Multi-Purpose tray/
all this Tray has is Paper Presence Sensor-& Last Paper Detection Sensor

A few other iRADVC's have the VR Width for their MP Tray-

the only available adj for your MP tray is -Margin Adjustment(1st-2nd side)/& Leading Edge Margin Adjustment(1st-2nd side) / and some other various nonsense items-
COPIER > ADJUST > FEED-ADJ > ADJ-MF in Service Mode (Level1)

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

Haha yea canon is weird like that. There should be markings on the bypass tray itself so you set the guide to a4r, hit the function > cst > mf-a4r. It should say ok. But what you're telling me if it copies fine then the size detection is ok. I'll have a looksee next time I'm at one of these puppies and let you know.

great thank you.

[northernlife]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

Haha yea canon is weird like that. There should be markings on the bypass tray itself so you set the guide to a4r, hit the function > cst > mf-a4r. It should say ok. But what you're telling me if it copies fine then the size detection is ok. I'll have a looksee next time I'm at one of these puppies and let you know.

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

teckat posted the instructions of what needs to be done. You'll need to go into service mode to perform the adjustments

I don't have A4 paper and the menu selections are not found. There's no (Lv.1) Copier > Function > CST > MF-A4R on this machine.

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

The machine accepts the COM10 size correctly (vertical) when you copy from the MP tray, but not when you print.

[northernlife]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

Can you please reply with how to correct the VR values? Thank you.

teckat posted the instructions of what needs to be done. You'll need to go into service mode to perform the adjustments

[c2230]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

If the bypass VR values are out of wack it will give you a similar symptom to this.

Can you please reply with how to correct the VR values? Thank you.

[northernlife]

Re: "Load Paper" When trying to print #10 envelopes from MS Word on C2230

If the bypass VR values are out of wack it will give you a similar symptom to this.