FS-534 Paper not exiting straight

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Konicatech
    Trusted Tech

    100+ Posts
    • Feb 2016
    • 131
    #1

    FS-534 Paper not exiting straight

    Hi,

    I have come across a Bizhub C554 with FS-534 finisher, and when the paper is exiting on the finisher, it is not exiting straight, its being pushed onto the output tray at an angle..

    Basically not ejecting as it should be.

    Anyone came across this before?

    Ta
    Tags: None
    • allan
      RTFM!!

      5,000+ Posts
      • Apr 2010
      • 5459
      #2
      Re: FS-534 Paper not exiting straight

      Make sure the paper is exiting the machine straight.
      The horizontal transport may be not closed properly or some debris in there somewhere.
      Last edited by allan; 07-03-2017, 09:17 PM.
      Whatever

        Comment

        • Guest
          #3
          Re: FS-534 Paper not exiting straight

          Originally posted by Konicatech
          Hi,

          I have come across a Bizhub C554 with FS-534 finisher, and when the paper is exiting on the finisher, it is not exiting straight, its being pushed onto the output tray at an angle..

          Basically not ejecting as it should be.

          Anyone came across this before?

          Ta
          I just did this morning! In the past i would replace belt and ejector finger on the one it's catching on. If it's a one time thing though, you can adjust both belts until both fingers line up again. Just hold one of the fingers back and force the other one to skip a couple teeth and line it right up. Works for me.


          Sent from my iPhone using Tapatalk

            Comment

            • allan
              RTFM!!

              5,000+ Posts
              • Apr 2010
              • 5459
              #4
              Re: FS-534 Paper not exiting straight

              Could also be the exit paddles that got worn out. Difficult to see the damage if you don't know the symptoms.
              Whatever

                Comment

                • Phil Walling
                  Technician
                  • Dec 2015
                  • 39
                  #5
                  Re: FS-534 Paper not exiting straight

                  That does sound as though you have an obstruction in there somewhere, causing the paper to skew. Try getting the paper to exit onto a different tray and see if it skews there.

                    Comment

                    • Synthohol
                      Certified Konica Expert

                      Site Contributor
                      5,000+ Posts
                      • Mar 2016
                      • 5746
                      #6
                      Re: FS-534 Paper not exiting straight

                      the 2 paddles are misaligned. you can press down on the belt thats behind and pull towards the exit to even them up. the belt will skip over the gear. thats fine, its what you want.
                      We know a thing or two because we've seen a thing or two.
                      The medication helps though...

                        Comment

                        • blackcat4866
                          Master Of The Obvious

                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 22960
                          #7
                          Re: FS-534 Paper not exiting straight

                          I think this thread covers it:
                          FS-534 alignment plate wearing. - Copytechnet.com
                          http://www.copytechnet.com/forums/konica-minolta/104455-fs-534-alignment-plate-wearing.html


                          =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            • s817
                              Technician
                              • Aug 2013
                              • 13
                              #8
                              Re: FS-534 Paper not exiting straight

                              check the bridge unit guide ( the upper guide )just prior to the
                              finisher entrance the paper can wear the guide( generally at the rear of guide)
                              look at the ridges to see if worn, you will need to look carefully
                              as it won't be worn by much but the paper catches on it and skews
                              part no. a3ep822100 guide/7 item 17

                              good luck

                                Comment

                                Previous template Next
                                Working...