C454e Printing not fusing and with shadows

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • Synaux
    Service Manager

    Site Contributor
    1,000+ Posts
    • Mar 2012
    • 1224
    #16
    Re: C454e Printing not fusing and with shadows

    The title says "C454e Printing not fusing and with shadows" when I think "not fusing" I think the toner is not adhering to the substrate. I did not see this very well in the photos...is that what is happening?

    If so:
    Why was the fuser recently replaced (I assume recently at a mere 25k).
    What is the meter count of the machine?
    What is the temp recorded in Service Mode for the fuser?

    Lots more to say but respond to the other comments first as well...as they are tackling the other issue.

    Also what is with the second picture--did you Saran wrap the print prior to photographing? First photo is not entirely helpful either. Please post top-down pictures or scans

      Comment

      • positiveg
        Trusted Tech

        250+ Posts
        • Jun 2018
        • 299
        #17
        Re: C454e Printing not fusing and with shadows

        Ok will work on then and then let you guys know. Tomorrow will work on the requested infom
        As for the fusing it's more like the edge of the paper there print is not as clear, strong, evident as the rest of the printed piece

        Sent from my SM-G955F using Tapatalk

          Comment

          • positiveg
            Trusted Tech

            250+ Posts
            • Jun 2018
            • 299
            #18
            Re: C454e Printing not fusing and with shadows

            Thanks all did a gradation/ image stabilisation. Found an awesome vid on youtube.
            Fixed the problem almost instantly. Still would probably run another set tomorrow again because on the video the tech did it three time, but with customers coming in the shop. I was only able to really get it done twice
            But it improved i can still see a bit lighter print at top left where the green (what I'm printing) is lighter than that to the bottom
            I'll get some pics for you guys to take a look, as I go back in the shop tomorrow with my tech to work on the Xerox C75. I'm just summing it up to 2020, lol

            Seriously thanks this site is wicked with the assistance that comes through
              👍 1

              Comment

              • positiveg
                Trusted Tech

                250+ Posts
                • Jun 2018
                • 299
                #19
                Re: C454e Printing not fusing and with shadows

                Originally posted by blackcat4866
                Ok, now you can begin to read the manual. You should start at the part about stabilization and gradation. =^..^=
                I went to look for manual but it was downloaded on a hard drive that went bad and I didn't upload it to my cloud drive
                I did contact the persons asking for another live link to re-download but they didn't respond, so I found a video online.

                Thanks again man

                  Comment

                  • blackcat4866
                    Master Of The Obvious

                    Site Contributor
                    10,000+ Posts
                    • Jul 2007
                    • 22960
                    #20
                    Re: C454e Printing not fusing and with shadows

                    I'm glad that you got it figured out. =^..^=
                    If you'd like a serious answer to your request:
                    1) demonstrate that you've read the manual
                    2) demonstrate that you made some attempt to fix it.
                    3) if you're going to ask about jams include the jam code.
                    4) if you're going to ask about an error code include the error code.
                    5) You are the person onsite. Only you can make observations.

                    blackcat: Master Of The Obvious =^..^=

                      Comment

                      • positiveg
                        Trusted Tech

                        250+ Posts
                        • Jun 2018
                        • 299
                        #21
                        Re: C454e Printing not fusing and with shadows

                        Yes it did thanks much

                        Sent from my SM-G955F using Tapatalk

                          Comment

                          Previous 1 2 template Next
                          Working...