C224 Bizhub Bypass Tray and Tray 2 switched

[tsbservice]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

I think the lower screw holds the PC210 front / right located^^

I don't think so. Like srvctec said it holds desk and mainbody together.

[Gift]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Glad you got it figured it out.

To be honest, I'm not even sure what I'm looking at in that picture with the 2 screws, it doesn't look familiar to me. Possibly the bypass tray mount?

I think the lower screw holds the PC210 front / right located^^

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Thanks. Now that the picture it's pulled back a bit, I can clearly see that now. What threw me off was the long screw that goes to the white glide roller for the tray. I didn't remember ever seeing that before, but then again, unless you are actually looking for it, sometimes things don't stick in memory.

I couldn't pull the tray out so I removed the left side and took out the paper behind the tray!
Thanks again femaster.

[femaster]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

it's located below tray 1
[ATTACH=CONFIG]47975[/ATTACH]

Thanks. Now that the picture it's pulled back a bit, I can clearly see that now. What threw me off was the long screw that goes to the white glide roller for the tray. I didn't remember ever seeing that before, but then again, unless you are actually looking for it, sometimes things don't stick in memory.

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Not sure what you have circled on top but the bottom circled screw is one of four screws that holds the machine to the cabinet it's setting on.

The circle on top is another screw but photo is dark.
IMG-9768.JPG
Problem has been fixed.
Thank you,

[srvctec]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

it's located below tray 1
[ATTACH=CONFIG]47975[/ATTACH]

Not sure what you have circled on top but the bottom circled screw is one of four screws that holds the machine to the cabinet it's setting on.

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Glad you got it figured it out.

To be honest, I'm not even sure what I'm looking at in that picture with the 2 screws, it doesn't look familiar to me. Possibly the bypass tray mount?

it's located below tray 1
IMG-9774.jpg

[femaster]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

There are two screws and catch on both side keeping the tray. I was able to remove only on the left side but not on the right side as shown on the below photo
[ATTACH=CONFIG]47972[/ATTACH]

Glad you got it figured it out.

To be honest, I'm not even sure what I'm looking at in that picture with the 2 screws, it doesn't look familiar to me. Possibly the bypass tray mount?

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

YES, I removed the side and found a paper behind the tray. Everything is back to normal.
Thanks femaster and blackcat.

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Not inside the tray. Pull out the tray and look behind the tray.

There are two screws and catch on both side keeping the tray. I was able to remove only on the left side but not on the right side as shown on the below photo
IMG-9768.JPG

[blackcat4866]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Not inside the tray. Pull out the tray and look behind the tray.

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

So ... do we know if there is paper behind the tray? =^..^=

The tray is clean - nothing else except the 8.5 x 11 paper.

I did search youtube but found only the how to do this do that. Look like only me or I am the first one having this proplem.

[blackcat4866]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

So ... do we know if there is paper behind the tray? =^..^=

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Sometime the tray 2 is seen as for 8 x 13 inch with bypass 8.5 x 11
IMG-9770.jpg

[hquang]

Re: C224 Bizhub Bypass Tray and Tray 2 switched

Thanks femaster for a quick help.
I could not remove the tray because there is another screw and catch on the right as shown on photo. And I see there are two other screws on the right as well.
(IMG-9768.JPG
I don't see any thing blocking the sensor in the tray. But there is a difference after removing and put back the paper in tray 2: new error message "replenish paper" and the "8.5 x 11" on the bypass tray has gone.
IMG-9765.jpgIMG-9769.JPG

Please tell me what to do next
thanks
Hien