Konica Minolta C250

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • JSC
    Gimp

    500+ Posts
    • Dec 2006
    • 618

    #1

    Konica Minolta C250

    Data light flashes, you can ping it but does not print. I have done a nic & nvram recovery, and it is on v3.05 firmware. Customer is chargable and very nice so i do not want to throw boards at it if i can help it.

    All help appreciated.
    The gene pool could use a little chlorine.
  • copytechman
    Senior Tech

    Site Contributor
    500+ Posts
    • Nov 2008
    • 947

    #2
    Did u actually reflash the machine firmware?
    Regards!
    A.

    Comment

    • JSC
      Gimp

      500+ Posts
      • Dec 2006
      • 618

      #3
      Originally posted by copytechman
      Did u actually reflash the machine firmware?
      Regards!
      A.

      Yep.
      The gene pool could use a little chlorine.

      Comment

      • mrwho
        Major Asshole!

        Site Contributor
        2,500+ Posts
        • Apr 2009
        • 4299

        #4
        DESCRIPTION: Unable to print. The data light blinks but no document prints (including a test page). SOLUTION ID: 238248
        SOLUTION: CAUSE: Incorrect Image Controller setting.
        SOLUTION: Set the proper Image Controller setting. To set the Image Controller mode, perform
        the following:
        1. Enter Service mode.
        2. Select System 2.
        3. Select Image Controller setting.
        4. Select Controller 0.
        5. Select End/Exit to exit the service mode.
        ' "But the salesman said . . ." The salesman's an asshole!'
        Mascan42

        'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'

        Ibid

        I'm just an ex-tech lurking around and spreading disinformation!

        Comment

        • copytechman
          Senior Tech

          Site Contributor
          500+ Posts
          • Nov 2008
          • 947

          #5
          K, no codes in machine (account tracking or anything?)

          A.

          Comment

          • copytechman
            Senior Tech

            Site Contributor
            500+ Posts
            • Nov 2008
            • 947

            #6
            Heh Beaten! What mrwho said!
            Does it show in the log/job history?

            Regards!
            A.

            Comment

            • JSC
              Gimp

              500+ Posts
              • Dec 2006
              • 618

              #7
              Originally posted by mrwho
              DESCRIPTION: Unable to print. The data light blinks but no document prints (including a test page). SOLUTION ID: 238248
              SOLUTION: CAUSE: Incorrect Image Controller setting.
              SOLUTION: Set the proper Image Controller setting. To set the Image Controller mode, perform
              the following:
              1. Enter Service mode.
              2. Select System 2.
              3. Select Image Controller setting.
              4. Select Controller 0.
              5. Select End/Exit to exit the service mode.
              Ok, it was set on Controller 3, so now i have selected controller 0 and entered that..............................now the networksettings button has disapeard.............
              The gene pool could use a little chlorine.

              Comment

              • mrwho
                Major Asshole!

                Site Contributor
                2,500+ Posts
                • Apr 2009
                • 4299

                #8
                Wait a couple of minutes... it's probably reinitializing...
                ' "But the salesman said . . ." The salesman's an asshole!'
                Mascan42

                'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'

                Ibid

                I'm just an ex-tech lurking around and spreading disinformation!

                Comment

                • JSC
                  Gimp

                  500+ Posts
                  • Dec 2006
                  • 618

                  #9
                  Originally posted by mrwho
                  Wait a couple of minutes... it's probably reinitializing...
                  Yea i was just being an arse machine is now up and running thanks dude, i'll add to your rep.
                  Although the 20ish year old chick here is so happy now she says if you can pop over she will take you out for a few drinks

                  I think the taxi might be a bit pricy!!!!!!!!!!!!!
                  The gene pool could use a little chlorine.

                  Comment

                  • mrwho
                    Major Asshole!

                    Site Contributor
                    2,500+ Posts
                    • Apr 2009
                    • 4299

                    #10
                    Thanks. Tell her I'd like to, but I'm a little bit far away - although if I ever go to the UK (about 1000miles), I'll call you to charge that drink!

                    Glad it worked. Cheers!
                    ' "But the salesman said . . ." The salesman's an asshole!'
                    Mascan42

                    'You will always find some Eskimo ready to instruct the Congolese on how to cope with heat waves.'

                    Ibid

                    I'm just an ex-tech lurking around and spreading disinformation!

                    Comment

                    Working...