C253 cannot boot

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Dimitar_Andonov
    Technician
    • Oct 2009
    • 10
    #1

    C253 cannot boot

    Dear friends,
    Have a problem with BH C253. I tried to yupdate firmware using CF card, but when i put card in the slot and turn on the machine, nothing happened. Display stayed black and star button light orange. I wait about half an hour, but nothing changed. Since that moment i couldn't start the machine. Try with diferent CF cards and different firmwares. Try to make NVRAM clear and recovery, but nothing change. Can you help me with adwice? Thanks a lot !!
    Tags: black, boot, button, c253, cards, cf card, clear, control panel, display, firmware, half, lef, light, nly, nvram, orange, recovery, retraction, sound, start, sudden, turn, wait
    • DCPS
      Trusted Tech

      100+ Posts
      • Mar 2008
      • 116
      #2
      Did you change the MFPB before or did this happen suddenly? You don't even have the sandglass on the display?

        Comment

        • RRodgers
          Service Manager

          1,000+ Posts
          • Jun 2009
          • 1947
          #3
          Try turning the copier off.... holding down the utility button and turn it back on, keep holding down the utility key (for a while) you should eventually see "Trouble reset" (I hope) if not.....
          Ummm....
          Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it.

            Comment

            • Dimitar_Andonov
              Technician
              • Oct 2009
              • 10
              #4
              DCPS and RRodgers, thanks a lot for ideas! Problem with the machine hapened suddennly. A day befre i tried to adjust Print area, but machine didn't response correctly to my intervention. No sandglass appeared- absolutely black hole. I try to enter trouble reset function, but with no success. I think that boot sector in MFPB was broken... any ideas how to recover it?

                Comment

                • RRodgers
                  Service Manager

                  1,000+ Posts
                  • Jun 2009
                  • 1947
                  #5
                  Does it sound like it's trying to boot? Might be a dead screen.
                  Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it.

                    Comment

                    • kmcopier
                      PSP

                      100+ Posts
                      • Oct 2008
                      • 183
                      #6
                      try R6 boot firmware, if that doesn't solved it MFPB!!

                        Comment

                        • Dimitar_Andonov
                          Technician
                          • Oct 2009
                          • 10
                          #7
                          RRodgers I heard only fans on the start and retraction mechanism of transfer roller. Kmcopier, is this some kind of special firmware? I try only with mass production ones. I didn't see such in infohub suport. RRodgers and Kmcopier, thanks a lot for replays!!!

                            Comment

                            • vijaysharma
                              Technician

                              50+ Posts
                              • Sep 2008
                              • 61
                              #8
                              Replace the NVRAM its fix the problem

                                Comment

                                • SmellsHot
                                  Head Tech

                                  500+ Posts
                                  • Dec 2009
                                  • 512
                                  #9
                                  start with operation panel!!!
                                  Everyone has the right to be stupid. Some people just abuse this privelage more than others

                                    Comment

                                    • Dimitar_Andonov
                                      Technician
                                      • Oct 2009
                                      • 10
                                      #10
                                      SmellsHot, thaks for idea, but i'm sure that panel is ok, i checked it. Vijaysharma, i'll try with new NVRAM. Thanks a lot to both of you!!!

                                        Comment

                                        • Dimitar_Andonov
                                          Technician
                                          • Oct 2009
                                          • 10
                                          #11
                                          NVRAM is OK......HMMM. Any ideas?

                                            Comment

                                            • copytechman
                                              Senior Tech

                                              Site Contributor
                                              500+ Posts
                                              • Nov 2008
                                              • 926
                                              #12
                                              If the ram chips, nvram and hdd are ok, and you've tried firmware... unless... did u ever unplug the control panel cable from the mfp board, that'll do it too, reseat the control panel cable @ both ends. Otherwise then all your left with is a damaged mfp board.. been there, done that!

                                              Regards!
                                              A.

                                                Comment

                                                • Dimitar_Andonov
                                                  Technician
                                                  • Oct 2009
                                                  • 10
                                                  #13
                                                  Thank Copytechman!!! Wish me luck.... I'm going to hell now

                                                    Comment

                                                    • Dimitar_Andonov
                                                      Technician
                                                      • Oct 2009
                                                      • 10
                                                      #14
                                                      Helloo friends,
                                                      Boot of MFP board was died. We change MFP and.....vollla....it works!!!. Thanks for help, all of you!!

                                                        Comment

                                                        • RRodgers
                                                          Service Manager

                                                          1,000+ Posts
                                                          • Jun 2009
                                                          • 1947
                                                          #15
                                                          Glad it worked out for ya.
                                                          Color is not 4 times harder... it's 65,000 times harder. They call it "TECH MODE" for a reason. I have manual's and firmware for ya, course... you are going to have to earn it.

                                                            Comment

                                                            Previous template Next
                                                            Working...