TA 5004i

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • delsignore2410@rogers.com
    Junior Member
    • Nov 2015
    • 5
    #1

    [Jamming] TA 5004i

    Hi All;
    I am running into jam 9310 on a TA 5004i using a Dual scan DP 7160. It only happens once in a while. It is pointing to the DP backside sensor.
    Has any one run into this jam code issue.
    Any ideas ?

    Sam .D
    Tags: 5004i, backside, jam, pointing, sensor
    • PrintWhisperer
      Trusted Tech

      250+ Posts
      • Feb 2018
      • 473
      #2
      Re: TA 5004i

      While your problem is not noted as part of this bulletin, the adjustments below are recommended for correct image timing detection for the DP-7160 upon installation (due to a potential problem with the SLANT sensing, which I have seen a few times as slanted copy output):

      [Adjustment procedures]
      Execute the procedures below. No Procedures to execute
      1
      Change [On/Off Config] of U075 (Adjust DP slant) from On to Off.
      2
      Detach the DP right hinge cover and angle limiter bracket to adjust the DP attachment position with the adjustment screw if it is necessary to adjust the leading edge image slant.
      3
      Detach the DP rear cover to adjust the DP height with the height adjustment screw on the DP left hinge if it is necessary to adjust the trailing edge image slant.
      4
      Execute [DP FU/FD(ChartB)*] of U411 (Scanner auto adjustment).
      *Execute [DP Auto Adj] if ChartB is not available.
      5
      Change [On/Off Config] of U075 (Adjust DP slant) from Off to On.
      6
      Execute the item below if necessary.
       U068: DP scanning position adjustment
       U070: DP magnification adjustment
       U072: Adjusting the DP original center
      7
      If it is necessary to fine-tune the leading edge timing, change [On/Off Config] of U075 (Adjust DP slant) from On to Off to execute U071 (Adjusting the DP leading edge Timing (The original image slant correction function is invalid if turning it off).
      *It is planned to upgrade the firmware to enable fine-tuning of the leading edge timing with the original image slant correction function turned on.


      Field Measure: Execute the above adjustment procedures when installing DP-7160/7170.
      "Being ignorant is not so much a shame, as being unwilling to learn" - Benjamin Franklin

        Comment

        • delsignore2410@rogers.com
          Junior Member
          • Nov 2015
          • 5
          #3
          Re: TA 5004i

          Originally posted by PrintWhisperer
          While your problem is not noted as part of this bulletin, the adjustments below are recommended for correct image timing detection for the DP-7160 upon installation (due to a potential problem with the SLANT sensing, which I have seen a few times as slanted copy output):

          [Adjustment procedures]
          Execute the procedures below. No Procedures to execute
          1
          Change [On/Off Config] of U075 (Adjust DP slant) from On to Off.
          2
          Detach the DP right hinge cover and angle limiter bracket to adjust the DP attachment position with the adjustment screw if it is necessary to adjust the leading edge image slant.
          3
          Detach the DP rear cover to adjust the DP height with the height adjustment screw on the DP left hinge if it is necessary to adjust the trailing edge image slant.
          4
          Execute [DP FU/FD(ChartB)*] of U411 (Scanner auto adjustment).
          *Execute [DP Auto Adj] if ChartB is not available.
          5
          Change [On/Off Config] of U075 (Adjust DP slant) from Off to On.
          6
          Execute the item below if necessary.
           U068: DP scanning position adjustment
           U070: DP magnification adjustment
           U072: Adjusting the DP original center
          7
          If it is necessary to fine-tune the leading edge timing, change [On/Off Config] of U075 (Adjust DP slant) from On to Off to execute U071 (Adjusting the DP leading edge Timing (The original image slant correction function is invalid if turning it off).
          *It is planned to upgrade the firmware to enable fine-tuning of the leading edge timing with the original image slant correction function turned on.


          Field Measure: Execute the above adjustment procedures when installing DP-7160/7170.

          Thanks,
          I will give this a try.

            Comment

            • craigster
              Trusted Tech

              100+ Posts
              • Apr 2016
              • 201
              #4
              Re: TA 5004i

              Had a brand new one do same thing and we replaced the sensor which fixed it.

                Comment

                • Debanon1
                  Junior Member
                  • Jan 2020
                  • 1
                  #5
                  Re: TA 5004i

                  Originally posted by delsignore2410@rogers.com
                  Hi All;
                  I am running into jam 9310 on a TA 5004i using a Dual scan DP 7160. It only happens once in a while. It is pointing to the DP backside sensor.
                  Has any one run into this jam code issue.
                  Any ideas ?

                  Sam .D

                    Comment

                    • Tonerkiller
                      Senior Tech

                      500+ Posts
                      • Oct 2012
                      • 669
                      #6
                      Re: TA 5004i

                      Are you guys leaving sim 75 off or on?

                        Comment

                        • blackcat4866
                          Master Of The Obvious

                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 23010
                          #7
                          Re: TA 5004i

                          Originally posted by Tonerkiller
                          Are you guys leaving sim 75 off or on?
                          The way I'm reading the information, there is a future firmware update aimed at correcting this issue. For now leave it OFF ... until the firmware comes out. I suspect that you'll probably have to re-run all those adjustments again, once the firmware is loaded. =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            • Tonerkiller
                              Senior Tech

                              500+ Posts
                              • Oct 2012
                              • 669
                              #8
                              Re: TA 5004i

                              Originally posted by blackcat4866
                              The way I'm reading the information, there is a future firmware update aimed at correcting this issue. For now leave it OFF ... until the firmware comes out. I suspect that you'll probably have to re-run all those adjustments again, once the firmware is loaded. =^..^=
                              That is what we are doing.
                              Thank you

                                Comment

                                Previous template Next
                                Working...