km6030 blurring in one section

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • digicor
    Service Manager
    1,000+ Posts
    • Jul 2008
    • 1130
    #1

    km6030 blurring in one section

    This km603 is enbolding, or blurring one section of the text about an 1/8 inch all the way down the page landscape or portrait and is in the same place every time.
    no matter what direction, i have run drum refresh , no fix it, cleaned everything in the drum section(corona wires,grid,eraselamps) i just cant seem to get a clue as to what is causing this, if it IS the drum itself, then wouldnt this blurring move from place to place? this is in the same spot everytime, even when i copy a page with this blur on it, the blur is is doubled up??? and its in the print as well not just copy...???
    anybody have any experience with this issue?Even my kyocera dealer's top service tech has not seen this problem,nor has an answer....this doesnt make him a bad tech....by the way .. lol
    Tags: None
    • HenryT2
      Senior Tech
      500+ Posts
      • Apr 2010
      • 962
      #2
      Re: km6030 blurring in one section

      Originally posted by digicor
      This km603 is enbolding, or blurring one section of the text about an 1/8 inch all the way down the page landscape or portrait and is in the same place every time.
      no matter what direction, i have run drum refresh , no fix it, cleaned everything in the drum section(corona wires,grid,eraselamps) i just cant seem to get a clue as to what is causing this, if it IS the drum itself, then wouldnt this blurring move from place to place? this is in the same spot everytime, even when i copy a page with this blur on it, the blur is is doubled up??? and its in the print as well not just copy...???
      anybody have any experience with this issue?Even my kyocera dealer's top service tech has not seen this problem,nor has an answer....this doesnt make him a bad tech....by the way .. lol
      Have you looked at the Dev unit ?
      How 'bout the fuser ?
      "The Serenity Prayer" . . .
      God grant me the serenity to accept stupid people , the courage to not waste my time and energy on them , and the wisdom to know that I cannot fix STUPID .

        Comment

        • JR2ALTA
          Service Manager
          Site Contributor
          1,000+ Posts
          • Feb 2010
          • 2010
          #3
          Re: km6030 blurring in one section

          It's the transfer belt.

          A PM kit is probably due (which has a new belt and charge rollers) as well as a good cleaning/lubing driving system.

            Comment

            • blackcat4866
              Master Of The Obvious
              Site Contributor
              10,000+ Posts
              • Jul 2007
              • 22599
              #4
              Re: km6030 blurring in one section

              I'm leaning in the same direction as JR Alta. The bearings and shafts in the transfer assy significantly wear by 1M prints. Are you getting light print with a dirty lead edge void? How about J41 jams?

              How many prints? Sample scan? =^..^=
              If you'd like a serious answer to your request:
              1) demonstrate that you've read the manual
              2) demonstrate that you made some attempt to fix it.
              3) if you're going to ask about jams include the jam code.
              4) if you're going to ask about an error code include the error code.
              5) You are the person onsite. Only you can make observations.

              blackcat: Master Of The Obvious =^..^=

                Comment

                • digicor
                  Service Manager
                  1,000+ Posts
                  • Jul 2008
                  • 1130
                  #5
                  Copies are perfect

                    Comment

                    • Zackuth
                      Trusted Tech
                      250+ Posts
                      • Aug 2009
                      • 448
                      #6
                      Re: km6030 blurring in one section

                      Get into the tech mode and go to U053. From there go to Seperate Setting RESIST MOTOR registration motor speed adj and adjust the speed. You will have to try them in increments of 5 to get a noticeable adjustment. I'm not sure if the speed shoud be increased or decreased. I've had this issue and this was the fix.
                      If at first you don't succeed, redefine success

                        Comment

                        Previous template Next
                        Working...