taskalfa 3050ci error after change dv m

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • AngusYoung
    Technician
    • Aug 2012
    • 22
    #1

    taskalfa 3050ci error after change dv m

    Changed in the printer development unit magenta and the print quality was poor.
    Magenta periods over the entire sheet. Calibration is performed.

    pic here https://plus.google.com/u/0/photos/1...20402926187457https://plus.google.com/u/0/photos/1...20402926187457
    Tags: None
    • darry1322
      Senior Tech

      Site Contributor
      500+ Posts
      • Oct 2010
      • 817
      #2
      Re: taskalfa 3050ci error after change dv m

      If it wasn't doing this before you changed the magenta developer, then the new unit is probably defective.

        Comment

        • AngusYoung
          Technician
          • Aug 2012
          • 22
          #3
          Re: taskalfa 3050ci error after change dv m

          Originally posted by darry1322
          If it wasn't doing this before you changed the magenta developer, then the new unit is probably defective.
          was
          CAM00082.jpg

          and now
          CAM00085.jpg

          period similar to the circle of the magenta shaft of the magnetic drum .
          And this problem does not occur for the first time. The last time helped the new firmware and cleaning contacts. What exactly helped in that time did not know and had a problem with yellow.

            Comment

            • blackcat4866
              Master Of The Obvious

              Site Contributor
              10,000+ Posts
              • Jul 2007
              • 22999
              #4
              Re: taskalfa 3050ci error after change dv m

              I'll have to agree with darry. If the problem is introduced with the new magenta developer, then that's the most likely source of the problem. =^..^=
              If you'd like a serious answer to your request:
              1) demonstrate that you've read the manual
              2) demonstrate that you made some attempt to fix it.
              3) if you're going to ask about jams include the jam code.
              4) if you're going to ask about an error code include the error code.
              5) You are the person onsite. Only you can make observations.

              blackcat: Master Of The Obvious =^..^=

                Comment

                • AngusYoung
                  Technician
                  • Aug 2012
                  • 22
                  #5
                  Re: taskalfa 3050ci error after change dv m

                  Originally posted by blackcat4866
                  I'll have to agree with darry. If the problem is introduced with the new magenta developer, then that's the most likely source of the problem. =^..^=
                  If the problem persists, and with another new development unit of the new kit?
                  And me, I immediately and the developing unit and drum.

                    Comment

                    • NeoMatrix
                      Senior Tech.

                      2,500+ Posts
                      • Nov 2010
                      • 3513
                      #6
                      Re: taskalfa 3050ci error after change dv m

                      Looks like a dev bias ground fault or ITB inner roller fault ???
                      Inauguration to the "AI cancel-culture" fraternity 1997...
                      •••••• •••[§]• |N | € | o | M | Δ | t | π | ¡ | x | •[§]••• ••••••

                        Comment

                        • blackcat4866
                          Master Of The Obvious

                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 22999
                          #7
                          Re: taskalfa 3050ci error after change dv m

                          Originally posted by NeoMatrix
                          Looks like a dev bias ground fault or ITB inner roller fault ???
                          I was thinking similarly:
                          check charge contacts
                          check transfer belt to HVT contacts

                          Is it OEM toner?
                          =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            • ES-OGT
                              Trusted Tech

                              100+ Posts
                              • Aug 2011
                              • 129
                              #8
                              Re: taskalfa 3050ci error after change dv m

                              Make sure you run the AC Calibration once you replace these. I've had that solve this problem before. Otherwise it's a bad DV unit.

                                Comment

                                • AngusYoung
                                  Technician
                                  • Aug 2012
                                  • 22
                                  #9
                                  Re: taskalfa 3050ci error after change dv m

                                  Originally posted by ES-OGT
                                  Make sure you run the AC Calibration once you replace these. I've had that solve this problem before. Otherwise it's a bad DV unit.
                                  u464 ?

                                    Comment

                                    • blackcat4866
                                      Master Of The Obvious

                                      Site Contributor
                                      10,000+ Posts
                                      • Jul 2007
                                      • 22999
                                      #10
                                      Re: taskalfa 3050ci error after change dv m

                                      Originally posted by AngusYoung
                                      u464 ?
                                      Yes. If you look at the insert, Kyocera recommends that you run U464 twice. Both before and after color registration. =^..^=
                                      If you'd like a serious answer to your request:
                                      1) demonstrate that you've read the manual
                                      2) demonstrate that you made some attempt to fix it.
                                      3) if you're going to ask about jams include the jam code.
                                      4) if you're going to ask about an error code include the error code.
                                      5) You are the person onsite. Only you can make observations.

                                      blackcat: Master Of The Obvious =^..^=

                                        Comment

                                        • FrK
                                          Junior Member
                                          • Feb 2013
                                          • 4
                                          #11

                                            Comment

                                            Previous template Next
                                            Working...