Ricoh MP C2500 Error Code SC672 on Startup.

[Rada]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

As it has been such a long time since I have seen one of these things, does it have a printer / scanner SD card?

Yes.

[TonerMunkeh]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

As it has been such a long time since I have seen one of these things, does it have a printer / scanner SD card?

[Rada]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Dear Friends,
I put back every thing to its place and only remove a Big SD Memory Card on the back of the machine. and machine take a long time on welcome screen and turned on and I tried to make a copy it was working fine. buts it was not going to printer and scanner mode. I tried 3 to 4 time by restarting the machine. every time it take long time to start. but not going to printer and scanner options. then I just leave it for a while. then I just put the USB cable in the printer to check didn't connect to my laptop. then I saw that screen and every thing is off. and only power light in on. then I tried to restart it. but every time only Power light is turning on nothing else. Can you tell me what is the problem.

Brothers Please guide me further. need your help.

[Rada]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Hi

We're the switches on the controller board? Switch 1 dictates booting from flash memory if off or SD card when on.

Switch 2 to 8 should not be changed.

Did you change these with the machine powered on?

Sent from my SM-N770F using Tapatalk

I Always turn power off before changing any thing. but once by mistake I didn't off the machine and change switch No. 8.

[davel]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

The more you do without knowing what the heck you are doing the worse it will become. Put the old thing out of its misery and update to a newer model.

[Polarbear]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Hi

We're the switches on the controller board? Switch 1 dictates booting from flash memory if off or SD card when on.

Switch 2 to 8 should not be changed.

Did you change these with the machine powered on?

Sent from my SM-N770F using Tapatalk

[Rada]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Did you remove HDD and Ram at the same time? Not a good idea afaik..

In case the unit has a java/vm card you can try and remove it, too.

Dear Friends,
I put back every thing to its place and only remove a Big SD Memory Card on the back of the machine. and machine take a long time on welcome screen and turned on and I tried to make a copy it was working fine. buts it was not going to printer and scanner mode. I tried 3 to 4 time by restarting the machine. every time it take long time to start. but not going to printer and scanner options. then I just leave it for a while. then I just put the USB cable in the printer to check didn't connect to my laptop. then I saw that screen and every thing is off. and only power light in on. then I tried to restart it. but every time only Power light is turning on nothing else. Can you tell me what is the problem.

[DRichard]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

In my experience this code generally means a controller replacement. Redoing thr connections won't hurt, but I can't recall once fixing that code without a replacement controller.

Sent from my SM-N770F using Tapatalk

...nor I.

[copier tech]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Thank you All for your Great help. I Tried things that you mentioned above but problem was the same. but Suddenly I saw a switch board (Picture is attached) that have a 8 switches. all are upside but switch number 1 and 8 was down. I turn them up one by one. now the situation is that when move both switch up(1&8) the same error comes SC672. But when I move down the switch number 1 only print start and then give a new Error SC819 (Picture is attached). and I like to tell you that at the start of problem it starts with this same error (SC819). Sc672 come letter. now its back to SC819. Please guide me.

[Rada]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

SC 672 is a communication error between the controller and the operation panel. It is usually caused by a bad connection. Disconnect and reconnect the harness going to the operation panel at both ends.

Thank you All for your Great help. I Tried things that you mentioned above but problem was the same. but Suddenly I saw a switch board (Picture is attached) that have a 8 switches. all are upside but switch number 1 and 8 was down. I turn them up one by one. now the situation is that when move both switch up(1&8) the same error comes SC672. But when I move down the switch number 1 only print start and then give a new Error SC819 (Picture is attached). and I like to tell you that at the start of problem it starts with this same error (SC819). Sc672 come letter. now its back to SC819. Please guide me.

[luca72]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Hi Friends,
I have a Ricoh MP C2500. When I m starting it, it is giving error SC672 on startup screen. after search on Google I tried to remove and reconnect HDD and RAM and restart it. but problem not solved. Can any one help me to remove this error? it is also not going to service mode. just stuck on startup screen.

try to disconnect and reconnect the controller and its connectors, try to turn on the machine with the hdd disconnected, but it is easy for it to be the failed controller

[Gift]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Did you remove HDD and Ram at the same time? Not a good idea afaik..

In case the unit has a java/vm card you can try and remove it, too.

[davel]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

Machine is very old, only hope is get a controller from a parts machine but I assume you are not an experienced tech so may be you need to buy a replacement machine.

[slimslob]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

What is that setting labeled? and how to set from off to off?

Since you are already getting the SC code, SP 5875 will just make things worse.

[anothertech]

Re: Ricoh MP C2500 Error Code SC672 on Startup.

check the setting of SP5875-001. if the setting is set to 1 (OFF) change it to 0 (OFF).

What is that setting labeled? and how to set from off to off?