ARDF DF3010 B802.01

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • tcypy1961
    Senior Tech

    500+ Posts
    • Feb 2009
    • 773
    #1

    [Misc] ARDF DF3010 B802.01

    Tags: error, misfeed, motor, paper
    • slimslob
      Retired

      Site Contributor
      25,000+ Posts
      • May 2013
      • 37047
      #2
      Re: ARDF DF3010 B802.01

      It would be really nice to know what the main frame model is as the service manual for the main frame has the trouble shooting information for service codes.

        Comment

        • tcypy1961
          Senior Tech

          500+ Posts
          • Feb 2009
          • 773
          #3
          Re: ARDF DF3010 B802.01

          Originally posted by slimslob
          It would be really nice to know what the main frame model is as the service manual for the main frame has the trouble shooting information for service codes.

            Comment

            • slimslob
              Retired

              Site Contributor
              25,000+ Posts
              • May 2013
              • 37047
              #4
              Re: ARDF DF3010 B802.01

              I am not sure what manual you are looking at but the DF3010 does not have a reverse motor. The first item to check for either is a home position sensor, Stopper for SC 700 and Pick-up Roller for SC 701. Both are mounted on the same bracket. The bracket is held in place by one screw and possibly a positioning tab. The screw could loose. If you take the back cover off you should see the bracket and sensors.

              Did this start happening immediately after the pickup, feed and reverse rollers were replaced? Not getting the feed shoe reassembled correctly will cause the problem. Something I have had junior techs do numerous times.

                Comment

                • tcypy1961
                  Senior Tech

                  500+ Posts
                  • Feb 2009
                  • 773
                  #5
                  Re: ARDF DF3010 B802.01

                  Originally posted by slimslob
                  I am not sure what manual you are looking at but the DF3010 does not have a reverse motor. The first item to check for either is a home position sensor, Stopper for SC 700 and Pick-up Roller for SC 701. Both are mounted on the same bracket. The bracket is held in place by one screw and possibly a positioning tab. The screw could loose. If you take the back cover off you should see the bracket and sensors.

                  Did this start happening immediately after the pickup, feed and reverse rollers were replaced? Not getting the feed shoe reassembled correctly will cause the problem. Something I have had junior techs do numerous times.
                  other than misfeeds this is the first problem I've encountered with this document feeder. My bad on motor. it says the pick up motor turns on clockwise, the original stopper HP sensor does not detect home position of the original stopper. possible causes defective original stopper HP sensor, defective pick motor, defective DF drive board for SC700. SC701 pick up roller HP error with same info??? SC700 is original stopper error.
                  Thanks!!!

                    Comment

                    • slimslob
                      Retired

                      Site Contributor
                      25,000+ Posts
                      • May 2013
                      • 37047
                      #6
                      Re: ARDF DF3010 B802.01

                      Originally posted by tcypy1961
                      other than misfeeds this is the first problem I've encountered with this document feeder. My bad on motor. it says the pick up motor turns on clockwise, the original stopper HP sensor does not detect home position of the original stopper. possible causes defective original stopper HP sensor, defective pick motor, defective DF drive board for SC700. SC701 pick up roller HP error with same info??? SC700 is original stopper error.
                      Thanks!!!
                      There is a section in the 4001 service manual for the DF. It has a couple of good images of the sensors and their bracket.

                        Comment

                        Previous template Next
                        Working...