Problem with MP9000. Please urgent help

[idplus2]

Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?

[rajmalini]

Re: Problem with MP9000. Please urgent help

Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?

pls cold reset your printer.

[idplus2]

Re: Problem with MP9000. Please urgent help

Thank you for your help but what do you mean by " Cold reset"?

[JustManuals]

Re: Problem with MP9000. Please urgent help

This Parts & Service Manual can now be purchased for $12.77 and downloaded immediately after payment from


Just Manuals, The Internet's largest selection of manuals ~ Instant Downloads


Paul@justmanuals.com

[fbkhan3]

Re: Problem with MP9000. Please urgent help

Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?

What else did you do with fuser? look for trap wire,bad Thermistor, Open Thermofuse or make sure Fuser is properly seated and connected to female connector in the rear,

good luck!

[Bantams]

Re: Problem with MP9000. Please urgent help

Did you actually replace the Web

[idplus2]

Re: Problem with MP9000. Please urgent help

Did you actually replace the Web

i replaced it by a fuser from another MP9000. Do i have to replace the web entirely from the one replaced?

[idplus2]

Re: Problem with MP9000. Please urgent help

pls cold reset your printer.

Thank you for your help but what do you mean by " Cold reset"?

[sharpmind]

Re: Problem with MP9000. Please urgent help

First, disconnect the HDD to check whether "Please Wait" still appears.If same problem, try to clean the drum potential sensor.That is my basic idea.

[totoro]

Re: Problem with MP9000. Please urgent help

Put the original fuser back in the machine and see what changes.

[certifiedxeroxtech]

Re: Problem with MP9000. Please urgent help

align the web padre or check the whole fusing unit.

[Avago]

Re: Problem with MP9000. Please urgent help

Good morning every body, i made a sp reset on my MP9000, SP1902-001 for the ccleaning web. Immediately after every work fine except i can't make copies and when i put my mp9000 on printer mode, i got "Please wait", i got also the start button red instead of green . Why i suppose to do to make the machine working?

I've had this one before on another model (mp5500 I think), you've told the machine there's a brand new web but in fact you've taken one from another machine which has probably used up some of the web already. the reading back from the arm sensor which sits on the web doesn't match what the machine expects and it throws the machine into a loop.
The old fusing web might not sort this out as the values are all over the place.

You need to put in a brand new web and the zero value you've entered will match the reading from the sensor. hope this helps

[Moza]

Format HDD sp-5832 should do the trick

[Masterchief]

Re: Problem with MP9000. Please urgent help

Make sue you have assessed the WEB condition and if needed that you have replaced it CORRECTLY, i know these fusers have the old 1060/1075 parts so im concerned as to the state of the termostats also

Let me know

Masterchef