Finisher FN6

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • swagreis
    Technician
    • Jun 2008
    • 92
    #1

    Finisher FN6

    when using sorting or stable sorting in offset tray of fn6 which atttached in AR-M450
    the paper comes in the finisher and pass till the last step which the paper or sorted papers which stabled together wil come out from finisher
    it jammed in finisher and still in it till u pull it out
    sometimes i noticed a skew in paper position in the place it jammed
    anyone can advise
    thanks
    Tags: finisher, fn6, pushed
    • blackcat4866
      Master Of The Obvious

      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22995
      #2
      The jams that I have come across are usually POD1S, MPPD3_S, MPPD4_S, MPPD5_S, with the paper skewing throughout the finisher or mailbox.

      Remove the pass-through portion of the finisher and examine the rearmost fins for paper cuts that delay and/or skew the paper. I can usually file or sand down these fins to remove the cut portions. It works fine with smaller fins, just not cut fins. While you're in there examine the gate to make sure it is not broken or cut. Also remove any noise damping foam from that solenoid.

      That should get you started. =^..^=
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • CopierTechofOmens
          Agitating Artificer

          250+ Posts
          • Jan 2009
          • 268
          #3
          I've also run into the frame on the top of the finisher being slightly pushed down causing jamming/skewing. FN6 has been discontinued and is harder to get parts for...
          sigpic

            Comment

            • blackcat4866
              Master Of The Obvious

              Site Contributor
              10,000+ Posts
              • Jul 2007
              • 22995
              #4
              So the only finisher option on the MX-M450 is a FN7 or its most recent reincarnation? =^..^=
              If you'd like a serious answer to your request:
              1) demonstrate that you've read the manual
              2) demonstrate that you made some attempt to fix it.
              3) if you're going to ask about jams include the jam code.
              4) if you're going to ask about an error code include the error code.
              5) You are the person onsite. Only you can make observations.

              blackcat: Master Of The Obvious =^..^=

                Comment

                • CopierTechofOmens
                  Agitating Artificer

                  250+ Posts
                  • Jan 2009
                  • 268
                  #5
                  As far as I know. Tried getting parts, and all our suppliers/dealers say it's discontinued. Only the parts that cross with the MS6 mail-bin stacker are available
                  sigpic

                    Comment

                    • blackcat4866
                      Master Of The Obvious

                      Site Contributor
                      10,000+ Posts
                      • Jul 2007
                      • 22995
                      #6
                      There certainly were a lot of problems with the F1-87 codes. It took us a while to figure it out, but when solved they run pretty good. =^..^=
                      If you'd like a serious answer to your request:
                      1) demonstrate that you've read the manual
                      2) demonstrate that you made some attempt to fix it.
                      3) if you're going to ask about jams include the jam code.
                      4) if you're going to ask about an error code include the error code.
                      5) You are the person onsite. Only you can make observations.

                      blackcat: Master Of The Obvious =^..^=

                        Comment

                        Previous template Next
                        Working...