MX-3110N Simulation

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • RSCA
    Trusted Tech

    100+ Posts
    • Jul 2008
    • 112
    #1

    MX-3110N Simulation

    It must be the end of the day on Friday. I'm setting up this machine. First time with the new series. The set-up says enter simulation with the front cover open to do dv calibration. From the main screen I press copy and I get a big message that says "Front Cover Open" that covers all the buttons. If I close the cover I get a message to install the toner cartridges. What am I missing? The manual is no help.
    Tags: install, main, manual, open, screen, set, setting, time, toner
    • Dark Helmet
      Senior Tech

      Site Contributor
      500+ Posts
      • May 2009
      • 835
      #2
      Re: MX-3110N Simulation

      double tap the home button and then touch the VER when the meters pop up. You can then enter P,*,C,* and do 25-2

      It's in the book to
      Evil will always triumph because good is dumb.

        Comment

        • Dark Helmet
          Senior Tech

          Site Contributor
          500+ Posts
          • May 2009
          • 835
          #3
          Re: MX-3110N Simulation

          Also make sure you have the latest firmware and fuser mod. There is a ton of firmware fixes for these puppies.
          Evil will always triumph because good is dumb.

            Comment

            • RSCA
              Trusted Tech

              100+ Posts
              • Jul 2008
              • 112
              #4
              Re: MX-3110N Simulation

              I got it now. Thank you. First time with a new machine is always interesting. Have a great weekend.

                Comment

                • tmaged
                  Owner/Service Manager

                  Site Contributor
                  1,000+ Posts
                  • Oct 2008
                  • 1867
                  #5
                  Re: MX-3110N Simulation

                  And do NOT even touch the machine while it's stirring the DV. You'll botch it & have to add new DV. Been there, done that. Total BS !!
                  Hope that helps !
                  -Tony
                  www.dtios.com
                  Become a fan on Facebook

                    Comment

                    • Akitu
                      Legendary Frost Spec Tech

                      Site Contributor
                      2,500+ Posts
                      • Oct 2010
                      • 2595
                      #6
                      Re: MX-3110N Simulation

                      Originally posted by tmaged
                      And do NOT even touch the machine while it's stirring the DV. You'll botch it & have to add new DV. Been there, done that. Total BS !!
                      Well I can say I'm quite happy to have not had ours interrupted during set up. What happened in your case, and why did you have to replace the DV?
                      Cthulhu for president! Why settle for the lesser evil?

                        Comment

                        • Dark Helmet
                          Senior Tech

                          Site Contributor
                          500+ Posts
                          • May 2009
                          • 835
                          #7
                          Re: MX-3110N Simulation

                          Originally posted by tmaged
                          And do NOT even touch the machine while it's stirring the DV. You'll botch it & have to add new DV. Been there, done that. Total BS !!
                          Your supposed to take the toners out

                          Im guessing the machine got bumped and some toner fell down the pipe and overtoned your dv?
                          Evil will always triumph because good is dumb.

                            Comment

                            • tmaged
                              Owner/Service Manager

                              Site Contributor
                              1,000+ Posts
                              • Oct 2008
                              • 1867
                              #8
                              Re: MX-3110N Simulation

                              Originally posted by Lawrence
                              Your supposed to take the toners out

                              Im guessing the machine got bumped and some toner fell down the pipe and overtoned your dv?
                              Actually it tells you to remove the toner if you try to run 25-2. As I explained to the hotline guy, the first time you replace the developer, there's going to be toner in the pipes. There's some glitch in the firmware that needs fixed. It's simply touching the display that screws it up. It gave us F2-41 & 42.
                              Hope that helps !
                              -Tony
                              www.dtios.com
                              Become a fan on Facebook

                                Comment

                                • Dark Helmet
                                  Senior Tech

                                  Site Contributor
                                  500+ Posts
                                  • May 2009
                                  • 835
                                  #9
                                  Re: MX-3110N Simulation

                                  Originally posted by tmaged
                                  Actually it tells you to remove the toner if you try to run 25-2. As I explained to the hotline guy, the first time you replace the developer, there's going to be toner in the pipes. There's some glitch in the firmware that needs fixed. It's simply touching the display that screws it up. It gave us F2-41 & 42.
                                  In that case I will not touch the display
                                  Evil will always triumph because good is dumb.

                                    Comment

                                    Previous template Next
                                    Working...