Phaser 7800 boot won't finish

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • denden4h
    Technician
    • Mar 2006
    • 31

    #1

    [Dead] Phaser 7800 boot won't finish

    If anyone has a seen this, I could sure use your help. Xerox Phaser 7800 starts the boot process, goes from the first green screen to the one that shows the current firmware version, then says it is shutting down. It then restarts and this is all you get. I tried new firmware and a new SD Card with no success. The unit has a finisher attached and on power up, nothing happens except you hear what sounds like either the hard drive or a fan. No motors, solenoids, or other sounds. I believe the LVPS may be the culprit, but I want to know if anyone has seen this issue before. Thanks for any suggestions.
  • Exok
    Senior Tech

    500+ Posts
    • Jun 2011
    • 750

    #2
    Re: Phaser 7800 boot won't finish

    You said you tried new software. Were you able to get it to load? What method did you use? Upgrade / AltBoot / Forced AltBoot ?

    What software version is on the machine and what version did you try to install?

    I experienced the same problem on this model and new software fixed it for me.

    Comment

    • denden4h
      Technician
      • Mar 2006
      • 31

      #3
      Re: Phaser 7800 boot won't finish

      I tried a forced reboot. It took a long time to load, but no changes.

      Comment

      • drewzif
        Trusted Tech
        • Jul 2013
        • 101

        #4
        Re: Phaser 7800 boot won't finish

        Is the forced alt boot for this machine the same process as a 7545 ?

        Trying the same process but it's not doing anything different. My machine is stuck in a boot loop.

        Comment

        • adriansto
          Service Manager

          Site Contributor
          VIP Subscriber
          1,000+ Posts
          • Nov 2007
          • 2383

          #5
          Re: Phaser 7800 boot won't finish

          Originally posted by drewzif
          Is the forced alt boot for this machine the same process as a 7545 ?

          Trying the same process but it's not doing anything different. My machine is stuck in a boot loop.
          Did you connected to machine and watched the sbc boot process ?

          Comment

          • drewzif
            Trusted Tech
            • Jul 2013
            • 101

            #6
            Re: Phaser 7800 boot won't finish

            Originally posted by adriansto
            Did you connected to machine and watched the sbc boot process ?
            Unfortunately I don't have the PWS software working so can't do that. I have been trying to get it running on a virtual machine but keep getting different errors.

            Comment

            • Mukasa
              Trusted Tech
              • May 2015
              • 178

              #7
              Re: Phaser 7800 boot won't finish

              Originally posted by drewzif
              Unfortunately I don't have the PWS software working so can't do that. I have been trying to get it running on a virtual machine but keep getting different errors.
              Hello my friend the HDD is not good,
              to correct your fault then look for another phaser 7800 HDD disk or a copy of its image, fix it there and also do a forced upgrade.

              Comment

              • drewzif
                Trusted Tech
                • Jul 2013
                • 101

                #8
                Re: Phaser 7800 boot won't finish

                Originally posted by Mukasa
                Hello my friend the HDD is not good,
                to correct your fault then look for another phaser 7800 HDD disk or a copy of its image, fix it there and also do a forced upgrade.
                We installed a new drive today (new out of box, from computer store, not xerox) and tried to alt boot, it does not ever enter the alt boot and load software.

                Comment

                • Mukasa
                  Trusted Tech
                  • May 2015
                  • 178

                  #9
                  Re: Phaser 7800 boot won't finish

                  Originally posted by drewzif
                  We installed a new drive today (new out of box, from computer store, not xerox) and tried to alt boot, it does not ever enter the alt boot and load software.
                  Sorry i didn't mean a new HDD , it must be from xerox stores or from phaser 7800 or it image please.

                  Comment

                  Working...