xerox work center 5765

[tbkarthic]

Re: xerox work center 5765

Yes, it is.

i have lvps and drum unit but still same anybody have some other idea? thanks for your replays friends

[xcopytech]

Re: xerox work center 5765

First follow 09-060 RAP procedure from service manual.
Go to commponent control and check hvps output to see which part of hvps make error.
Did you check developer assy?

[CopierTechofOmens]

Re: xerox work center 5765

Also try cleaning the Transfer and main charge coros first

[tbkarthic]

Re: xerox work center 5765

Also try cleaning the Transfer and main charge coros first

i already did that but same

[Samuel Ortega]

Re: xerox work center 5765

By the imagenes of the messages showed by the workcentre, for the code xerographic fault, need to replace the cartridge of the drum and give him service of maintenance to the workcentre, the HVPS this well

[tbkarthic]

Re: xerox work center 5765

By the imagenes of the messages showed by the workcentre, for the code xerographic fault, need to replace the cartridge of the drum and give him service of maintenance to the workcentre, the HVPS this well

sorry i can't understand i have already replaced durm unit and hvps and lvps and dc controller pcb no more changes on that machine. this machine firmware is tooo costly i dont have interest in spend money for that

how to clear maintenance count?

[Corder]

Re: xerox work center 5765

sorry i can't understand i have already replaced durm unit and hvps and lvps and dc controller pcb no more changes on that machine. this machine firmware is tooo costly i dont have interest in spend money for that

how to clear maintenance count?

There's no any maintenance counter as far as I know.

[xcopytech]

Re: xerox work center 5765

Check wiring from hvps to developer assy.

[bluebear]

Re: xerox work center 5765

Hi, forum please correct me if am wrong in saying if the gentleman instigate the alboot software to his machine, the machine is more or less reset to factory default and for that matter a new firmware might not be required for fault / diagnostics purposes?

Unless his intension is to upgrade the current firmware and not necessarily for the troubleshooting reasons.

I ask this question so that he can narrow down the scoop of possiblefaults, this could be a fualty sensor or sensor corvered in waste toner.

[Corder]

Re: xerox work center 5765

Hi, forum please correct me if am wrong in saying if the gentleman instigate the alboot software to his machine, the machine is more or less reset to factory default and for that matter a new firmware might not be required for fault / diagnostics purposes?

Unless his intension is to upgrade the current firmware and not necessarily for the troubleshooting reasons.

I ask this question so that he can narrow down the scoop of possiblefaults, this could be a fualty sensor or sensor corvered in waste toner.

More likely it's the wiring.

[adriansto]

Re: xerox work center 5765

sorry i can't understand i have already replaced durm unit and hvps and lvps and dc controller pcb no more changes on that machine. this machine firmware is tooo costly i dont have interest in spend money for that

Remove transfer /detack unit from machine and try again to make copies.
Watch if the paper start to feed and where it stop.

[tbkarthic]

Re: xerox work center 5765

Remove transfer /detack unit from machine and try again to make copies.
Watch if the paper start to feed and where it stop.

i checked paper stop position for first tray stop on drum unit and form 2nd tray and 3 or 4th tray stop on left door front edge on developing unit bottom, i have checked paper path sensors its are working

[xcopytech]

Re: xerox work center 5765

Did you test hvps output from diagnostic (dc330)?
Did you check wiring from hvps to developer assembly?

[Richard.Xerox]

Re: xerox work center 5765

Just had a call for this same fault the other day, resolved by replacing the transfer/detack unit (which should be replaced when changing the drum)

Might not be that but it's the first place to start.

[nilak]

Re: xerox work center 5765

Check first if CR16 is light on on IOT board (Top, Left). If it is check on F1 or PJ27 pins1,2 for true 24v. If CR16 is off or 24v are below 23.2v unplug HVPS from IOT and power again! if it doesn't get them back go for 24v Rap.
If not - plug the HVPS back and try to unplug Detack, Transfer and Developer Bias one by one (with POPO) and check if 09-060 will disappear!
Still not get the short? - try the HVPS wires (unplugged) one by one to the ground for shorting (47k is still short)!
There is no so much left - IOT, IOT corruption, arcing and so on...