I need SERVICE MANUAL SHARP AR-M205

[Guest]

I need SERVICE MANUAL SHARP AR-M205

[mannu]

i will sand u give your mail id

[keddada]

my dear!

Hi,

First than you for the caring, & this's my email ted_jani@yahoo.fr.

best regards.

[wangchaoguis]

Hi,
mannu.I need SERVICE MANUAL SHARP AR-M205 too.Can you send it to me? my email:wangchao305503@hotmail.com Thanks.

[johnnyjamjet]

Sharp Arm 205

Hi i have a manual (pdf)
Where shoul i send it?

[mannu]

find the att 4 sharp manuals

plz find the att

[johnnyjamjet]

plz find the att

plz find the att

Sorry i don't understand

[mannu]

Jhon I Mail The Service Manual Oke

[wangchaoguis]

Thanks mannu.

[ntbinh_yb]

I need Sharp AR-M206 service manual document

Sharp AR-M206 Error code H4-00. Who can help me?

[johnnyjamjet]

the heat roller didn't reach the required temp in the time allowed, test the heat lamp with sim 5-2 (diag code #,*,c,*) if the lamp works, if could be the thermostat or just a clich. try a reset with sim code 14 first to see what happens.

[Kado1]

thanks.

[printerguy]

Sharp AR-M205

Looking for a manual for this machine. Can you send one via e-mail? Dan@RMPR.net.

Getting E-7 error and when scanning the lamp sometimes turns off for no reason. Any suggestions?

Thanks!

[mickspace]

Sharp AR-M206 Error code H4-00. Who can help me?

H4-00
Cause Thermistor abnormality
Heater lamp abnormality
Thermostat abnormality
Control PWB abnormality
Check
and
remedy
Use SIM 5-02 to check the heater lamp blinking
operation.
When the lamp blinks normally.
Check the thermistor and its harness.
Check the thermistor input circuit on the control
PWB.
When the lamp does not light up.
Check for disconnection of the heater lamp and
the thermostat. Check the interlock switch.
Check the power PWB and the lamp control
circuit on the MCU PWB.
Use SIM 14 to clear the self diagnostic display.
Or Install New Fusing unit, easier and cheaper..

[mickspace]

Looking for a manual for this machine. Can you send one via e-mail? Dan@RMPR.net.

Getting E-7 error and when scanning the lamp sometimes turns off for no reason. Any suggestions?

Thanks!

If you hold the start button it will show the rest of the code. If it is E7-10, do you have a doc feed, if so remove the slit glass and clean the underside, at either end of the slit glass, there should be a little sticker tab, on the top (where the paper passes) this sticker has white on the under side, it is the reference point for the lamp. I will attempt to e mail a manaul..

E7 01 Content Duplex model memory error
Detail The memory capacity for the duplex model
machine is improper. Insufficient memory
capacity
Cause The memory capacity of the MCU PWB is
improper.
Check
and
remedy
Use SIM 26-39 to check that the memory
capacity is 32MB. If it is not 32MB, replace the
MCU PWB with a suitable one.
E7-02 Code
Content LSU trouble
Detail The BD signal from the LSU cannot be
detected in a certain cycle. (Always OFF or
always ON)
Cause LSU connector or LSU harness defect or
disconnection
Polygon motor rotation abnormality
Laser beams are not generated.
MCU PWB abnormality.
Check
and
remedy
Check connection of the LSU connector.
Execute SIM 61-03 to check the LSU
operations.
Check that the polygon motor rotates normally.
Check that the laser emitting diode generates
laser beams.
Replace the LSU unit.
Replace the MCU PWB.
-E7-10 Code- Content Shading trouble (Black correction)
Detail The CCD black scan level is abnormal when
the shading.
Cause Improper connection of the CCD unit flat cable
CCD unit abnormality
MCU PWB abnormality.
Check
and
remedy
Check connection of the CCD unit flat cable.
Check the CCD unit."