Copier Porn
We were talking about copier porn today. You know... pictures of copiers with their covers off. We couldn't find anything good unfortunately, So.... lay it on me! What's your best copier porn?
-
-
Re: Copier Porn
Well, here is one machine that's all burnt out (thanks to another member)."You can't trust your eyes, if your mind is out of focus" --
-
Re: Copier Porn
Do cats count? In all my cat pictures, the cats are naked. This is Honey. See? No clothes. She hates clothes.:
Honey.jpg
The rest of these are fairly random photos:
Yes. One tech can remove the imaging drawer from a PRO1052.
PRO1052.jpg
How do you keep staple trimmings from shorting out your FS-532 finisher controller? Use really big refrigerator magnets:
Finisher.jpg
How does a KM-8000i look when you've replaced every individual part of the bridge unit? Be sure to include the exit sensor. You know, the part it actually needed:
KM-8000i.JPG
=^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: Copier Porn
I wouldn't mind seeing the KM-1 sans covers.
But I like 'em like that.Somewhere there is a tree working hard to produce oxygen for you to live, NOW GO APOLOGIZE TO IT!Comment
-
Re: Copier Porn
How about some sexy trim on a UFR.
Each time I wink at her she winks back, love her eye colour.
Is she inviting?
Don't like her biting though.Comment
-
Re: Copier Porn
20160718_090850.jpg20160727_135041.jpg
The first one a memory expansion card from back in times when you had to add memory to your computer. This card held about 4mb.
The sesond is the underneath of a lexmark xm3150 that i worked on today to replace the input sensor. Anyone going to do this, well let me just put it this way. This is the most absurd repair description i have ever had to do. look in the service manual and see and it is not easy. I did it another way, cut and solder, but you still have to remove parts, that you have to have dexterity to put back.THE ONLY THING FOR EVIL TO TRIUMPH IS FOR GOOD MEN TO DO NOTHING..........edmund burkeComment
-
-
Last edited by ZOOTECH; 07-28-2016, 03:16 AM."You can't trust your eyes, if your mind is out of focus" --Comment
-
Re: Copier Porn
I've changed a few of those paper pickup units on the larger Lexies.
What a treat!? First I have to find somebody capable of helping me lift the engine off the base. Then remove consumables and cassettes, and tip over the engine on it's back. Of course there's not 4mm of extra wire to release the harness from the looms. =^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: Copier Porn
and cut the cable near the frame to detach the sensors.
9 Remove the other half of the cable from the printer
Installation notes:
a Install the duplex sensor, followed by the input sensor.
b Route the cable using the new path.
c Secure the cable near the lift plate gearbox using cable ties. Cut off any excess cable tie.THE ONLY THING FOR EVIL TO TRIUMPH IS FOR GOOD MEN TO DO NOTHING..........edmund burkeComment
-
Re: Copier Porn
with Riso's we would still understand.WhateverComment
Comment