iRC3170 - replacing HDD, firmware update

[cuseeo]

Hello

Printer Canon iRC3170, after replacing the disk and uploading software (+ language, RUI, etc.), the printer will not start. A progress bar appears, comes to the middle and the device does not respond.

Please help, what am I doing wrong?

greetings
Jacob

[charm5496]

Re: iRC3170 - replacing HDD, firmware update

check your connections on the main controller. reseat your RAM and boot rom. When yoyu installed the firmware did you overwrite all?

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

Yes, I did. I formated HDD and installed firmware with overwrite all.

How can I reset RAM and boot rom?

greetings
Jacob

[zoraldinho]

Re: iRC3170 - replacing HDD, firmware update

Tipe of disc?
Firmware version?

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

HDD - Seagate ST340014A
Firmware ver. 40.01

greetings
Jacob

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

I bought this device without a disc already. The previous owner probably dismantle the disc for save private data.

greetings
Jacob

[teckat]

Re: iRC3170 - replacing HDD, firmware update

/
make sure u have only one version of SST on Laptop

remove the memory/ clean ends & re-seat it

iRC3100 SERIES
Supported HDD's in the new HD-Format_v00.12 ITF File

your's is listed below/where did u purchase this HDD from HDWN 'IC35L040AVER07-0

HDWN 'IC35L040AVVA07-0

HDWN 'IC35L060AVER07-0

HDWN 'IC35L080AVVA07-0

HDWN 'QUANTUM FIREBALLP AS40.0

HDWN 'QUANTUM FIREBALLP AS60.0

HDWN 'FUJITSU MPG3409AH E

HDWN 'Maxtor 4D040H2

HDWN 'SAMSUNG SP4002H

HDWN 'SAMSUNG SV4002H

HDWN 'MAXTOR 6L040J2

HDWN 'MAXTOR 6L060J3

HDWN 'IC35L060AVV207-0

HDWN 'SAMSUNG SV0401H

HDWN 'SAMSUNG SP0411N

HDWN 'SAMSUNG SV0411N

HDWN 'HDS722540VLAT20

HDWN 'ST340014A

HDWN 'ST340015A

HDWN 'HDS728040PLAT20

HDWN 'Hitachi HDS721680PLAT80

HDWN 'WDC WD800BB-22JHC0

HDWN 'TOSHIBA MK1665GSX

HDWN 'Hitachi HTS545016B9A300

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

make sure u have only one version of SST on Laptop

I have only one version - 4.11

iRC3100 SERIES
Supported HDD's in the new HD-Format_v00.12 ITF File

I have only v00.09 ITF File

So you dont know if the machine was working before you bought it?

Machine was working fine, I saw it before.

There is one error during update:

BROWSER... version up... error

And should I format BOOTDEV or ALL, becouse if I try to run ALL format there is error message??

Is 40.01 the newest version to iRC3170 ?

greetings
Jacob

[zoraldinho]

Re: iRC3170 - replacing HDD, firmware update

Yes it is.

[teckat]

Re: iRC3170 - replacing HDD, firmware update

v40.01 is last version

I believe the 3170 uses a 80GB HDD & THE 3100 a 40GB HDD/ 40GB will not work in the 3170

The ALL_HDF batch file does NOT format the HDD. The HDD must be formatted by using the HDFormat file. On the newer model machines, you must connect to the device in 'Single Mode' to format the HDD with the HDFormat file.

If you replace the HDD on a machine, the HDD must be formatted using the HDFormat file BEFORE performing a batch install with the ALL_HDF batch file. Otherwise, the ALL_HDF batch install will fail.



sorry, that v00.12 Format file was for iRC3100 PRINTER

your HDD is listed in the iR3100 format file list- that does not mean it will be accepted in the 3170/ unless it was purchased from Canon as a OEM

when u select SINGLE to format the 3170 HDD - what is the SST error message EXACTLY




your HDD may not be supported for the iR3170/ The HD Format v00.09 .itf file is encrypted , so u are not able to see supported HDD's

if u did not purchase this HDD from Canon

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

when u select SINGLE to format the 3170 HDD - what is the SST error message EXACTLY

Error response:Process has ended in error.

<<< FileName >>>
HDDFormatALL:C:\ServTool\iRCXXXX\HDFormat\XXxxv000 9\iRCXXXX-XXxx0009-HDFormat.ift


Module : SendFile() - 5

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

I changed disk to WD Caviar WD800 (80gb), unfortunately is the same effect.

These disks are NOT provided by Canon, it's normal disk from PC.

Any ideas ?

greetings
Jacob

[cuseeo]

Re: iRC3170 - replacing HDD, firmware update

Okay, I know that I should prapare hard disk to work in this machine. Can anybody help me?

greeting
Jacob

[charm5496]

Re: iRC3170 - replacing HDD, firmware update

the HDD format has to be done at the machine through the SST for the firmware to load. Where did you get the firmware for this unit? Did you go in and modify the ift file? If so make sure it is in a read only format after changing it. The Western Digital HDD should be supported, but if it is not you have to put the SN of that HDD in that file so the SST can read it.

[teckat]

Re: iRC3170 - replacing HDD, firmware update

Okay, I know that I should prapare hard disk to work in this machine. Can anybody help me?

greeting
Jacob

How exactly are u using the SST to format this HDD ?????

for the iRC3170
The HD Format v00.09 .itf file is encrypted , so u are not able to see supported HDD's