paper output

[pc123321]

paper output at the end of half inch to 3/4inch there is an wave form (not flat) why ?
80lb texst coated
100lb test coated set at heavy 1
80lb cover coated set at heavy 2
80lb 100lb texst go by bypass tray set heavy 1
80lb text by pass heavy 1 --always jam at fuser
or 80lb ,100lb text set plain ---how about fuser
100lb cover pass through fuser ----result is nightmare return
all that is c3220 model
any suggestion are welcome thanks

[kiwitech]

Re: paper output

check the shaft with about six black rubber rollers ( about 20mm diameter ) on it just after the fuser exit. these rollers become soft and sticky and came become deformed

[aakash@24]

Re: paper output

paper output at the end of half inch to 3/4inch there is an wave form (not flat) why ?
80lb texst coated
100lb test coated set at heavy 1
80lb cover coated set at heavy 2
80lb 100lb texst go by bypass tray set heavy 1
80lb text by pass heavy 1 --always jam at fuser
or 80lb ,100lb text set plain ---how about fuser
100lb cover pass through fuser ----result is nightmare return
all that is c3220 model
any suggestion are welcome thanks

faced the same problem in 3570.for me the cause was delay in paper transport.replaced the feed rollers and is going good till now.

[teckat]

Re: paper output

paper output at the end of half inch to 3/4inch there is an wave form (not flat) why ?
80lb texst coated
100lb test coated set at heavy 1
80lb cover coated set at heavy 2
80lb 100lb texst go by bypass tray set heavy 1
80lb text by pass heavy 1 --always jam at fuser
or 80lb ,100lb text set plain ---how about fuser
100lb cover pass through fuser ----result is nightmare return
all that is c3220 model
any suggestion are welcome thanks

--------------------------------------Canon Copier Media Guide_BW--Color.pdf

agree about checking those black exit rollers > they turn to mush (squeeze them to test)
Jam 0207_INTERNAL DEL ROLL2.JPG

check for flat spot on fix roller


tech tip---Do Not select HEAVY 1 or HEAVY 2 on any of that paper
that is a lesson learned on this model


Heavy 1*= Heavy 1 paper is from 28 lb bond to 110 lb index (106 to 209 g/m2).--PAPER DRAW, STACK BYPASS & PAPER DECK
Heavy 2*= Heavy 2 paper is from 80 lb cover to 140 lb index (210 to 253 g/m2).-- STACK BYPASS ONLY

---

• Basis WeightCaliper Finish or Texture, refers to the surface smoothness of the paper. Paper that is too rough will wear out pick-up rollers, paper guides, and other components on the paper path prematurely. A rough surface finish also degrades the quality of printed output. The peaks and valleys on the paper cause poor toner adhesion, a striped appearance, or characters that have broken corners. Paper that is too smooth results in misfeeds, poor toner adhesion, and washout.
• GrainOpacityGain CurlCut Edge Condition

[pc123321]

Re: paper output

--------------------------------------[ATTACH]22475[/ATTACH]

agree about checking those black exit rollers > they turn to mush (squeeze them to test)
[ATTACH=CONFIG]22473[/ATTACH]

check for flat spot on fix roller


tech tip---Do Not select HEAVY 1 or HEAVY 2 on any of that paper
that is a lesson learned on this model


Heavy 1*= Heavy 1 paper is from 28 lb bond to 110 lb index (106 to 209 g/m2).--PAPER DRAW, STACK BYPASS & PAPER DECK
Heavy 2*= Heavy 2 paper is from 80 lb cover to 140 lb index (210 to 253 g/m2).-- STACK BYPASS ONLY

---

• Basis WeightCaliper Finish or Texture, refers to the surface smoothness of the paper. Paper that is too rough will wear out pick-up rollers, paper guides, and other components on the paper path prematurely. A rough surface finish also degrades the quality of printed output. The peaks and valleys on the paper cause poor toner adhesion, a striped appearance, or characters that have broken corners. Paper that is too smooth results in misfeeds, poor toner adhesion, and washout.
• GrainOpacityGain CurlCut Edge Condition

part number: FB6-4862-000 is that correct ?

[teckat]

Re: paper output

FB6-4862-000 1 ROLLER, INTERNAL DELIVERY