Bizhub 601 has acute autism...

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Synaux
    Service Manager

    Site Contributor
    1,000+ Posts
    • Mar 2012
    • 1224
    #1

    Bizhub 601 has acute autism...




    Here is why I am fooling with the Frimware:
    1) Printing to the MFP has become extraordinarily slow especially with PS drivers (used different computers, different drivers, reset all settings, manually changed the adapter speed, eliminated the network and more).
    2) When printing, the image is shifted about 1/4" down the page (toward the operator side) regardless of the tray used and it doesn't happen all the time.
    Both of these issues manifested on the same day.
    Tags: None
    • blackcat4866
      Master Of The Obvious

      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22960
      #2
      Re: Bizhub 601 has acute autism...

      If you can set up TCP/IP but cannot view the webpage or print I would think that your IC208 print controller is toast. =^..^=
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • Synthohol
          Certified Konica Expert

          Site Contributor
          5,000+ Posts
          • Mar 2016
          • 5746
          #3
          Re: Bizhub 601 has acute autism...

          is the firmware correctly placed on the stick?
          you also need printer controller firmware G80-35, slow printing and no webpage display in browser thats where i'd start.
          you update firmware through ISW in service mode, not boot into it. not like the series of this century.
          • Create the BW75_60 or LoadableDeviceDriverROM folder directly under the USB memory route.
          • When copying the firmware to the memory, be sure to copy ".bin" file and ".sum" file or ".drv" file
          and ".sum" file at the same time.
          • Be sure to copy the files of each firmware to the USB memory in the configuration of the folders
          shown in the below.
          • In bizhub751/601, [Image_controller] folder is not used. (Composition of the folder is common
          with bizhub 750/600. )
          • If the copying is not completed correctly, a message " The data is not found" is displayed on the
          panel when the ISW files are selected.
          BW75_60
          MFP_controller
          Operation_message
          Image_controller
          Printer_controller
          Finisher_controller
          Fax_controller
          LoadableDeviceDriverROM
          Attached Files
          We know a thing or two because we've seen a thing or two.
          The medication helps though...

            Comment

            • Synaux
              Service Manager

              Site Contributor
              1,000+ Posts
              • Mar 2012
              • 1224
              #4
              Re: Bizhub 601 has acute autism...

              Originally posted by Synthohol
              is the firmware correctly placed on the stick?
              you also need printer controller firmware G80-35, slow printing and no webpage display in browser thats where i'd start.
              you update firmware through ISW in service mode, not boot into it. not like the series of this century.
              G80-35 is for "Machines that had replacement-processor boards installed during production can be identified by a square
              blue label next to the serial number on both the machine and the shipping carton. "
              G00-31 is for the FS-524/FS-610
              Here is the doc: 8088.pdf
              Also, I feel like a total dink...I thought it updated upon power cycle. I am writing the firmware now. Thanks!

                Comment

                • Synaux
                  Service Manager

                  Site Contributor
                  1,000+ Posts
                  • Mar 2012
                  • 1224
                  #5
                  Re: Bizhub 601 has acute autism...

                  Originally posted by blackcat4866
                  If you can set up TCP/IP but cannot view the webpage or print I would think that your IC208 print controller is toast. =^..^=
                  Lets hope not, but I got some more testing to do now
                  *Edit* I can view page scope after I enabled DHCP

                  This confuses me a little....

                  PC-32 “Printer Controller Firmware” 1-19-2009
                  “Printer_controller
                  57aa000c0g320000.bin / 57aa000c0g320000.sum
                  57ba000c0g320000.bin / 57ba000c0g320000.sum”
                  Whereas MFP-20 is called “MFP Firmware” 12-13-2010
                  “- Printer_controller
                  57aa000c0g340000.bin / 57aa000c0g340000.sum [bizhub 751]
                  57ba000c0g350000.bin / 57ba000c0g350000.sum [bizhub 601]”

                  The PC-32 is in the base firmware section online, but I think should be a "special firmware" and superseded by MFP-20?

                  Wrote firmware (MFP-20) and had to format HDD
                  PS drivers still transfers data in 4kb chunks per second...

                    Comment

                    Previous template Next
                    Working...