Konica C6000: Gamma correction abnormality

[qmuadhi]

Re: Konica C6000: Gamma correction abnormality

not that i saw, its PS or XPS.

How do u get xps drivers

Sent from my SM-A600F using Tapatalk

[Synthohol]

Re: Konica C6000: Gamma correction abnormality

LMGTFY ,--click here

[Rohullah]

Re: Konica C6000: Gamma correction abnormality

mandatory adjustments after replacing the laser(s)

After replacing the writing unit /K, conduct the following item.
- Cleaning the dust proof glass (Refer to F.5.2.1 - Cleaning the
dust proof glass)
- Writing initial position memory (Skew initial position memory)
(Refer to I.5.3.9 Skew Initial Position Memory (Printer Adjustment -
Writing Initial Pos. Memory))
- I/O Check Mode (LD1 to LD8 alarm data clear, LD alarm
measurement) (Refer to I.5.7.1 I/O Check Mode)
- CD-Mag. Skew Adj. (Refer to I.5.3.13 CD-Mag. Skew Adj.
(Printer Adjustment))
- Restart Timing Adjustment (Refer to I.5.3.1 Restart Timing
Adjustment (Printer Adjustment))
- Color Registration Auto.Adj. (Refer to I.5.3.10 Color Registration
Auto.Adj. (Printer Adjustment))
- Color Registration Manual (Refer to I.5.3.11 Color Registration
Manual (Printer Adjustment))
- Gamma Automatic Adjustment (Refer to I.5.4.7 Gamma
Automatic Adj. (Drum Peculiarity Adjustment))
- Beam Pitch Adjustment (Refer to I.5.3.14 Beam Pitch Adjustment
(Printer Adjustment))
- Moire Adjustment (Refer to I.5.3.15 Moire Adjustment (Printer
Adjustment))
8. After replacing the writing units /Y, /M, /C, conduct the following
item.
- Cleaning the dust proof glass (Refer to F.5.2.1 - Cleaning the
dust proof glass)
- Writing initial position memory (Skew initial position memory)
(Refer to I.5.3.9 Skew Initial Position Memory (Printer Adjustment -
Writing Initial Pos. Memory))
- I/O Check Mode (LD1 to LD8 alarm data clear, LD alarm
measurement) (Refer to I.5.7.1 I/O Check Mode)
- Color Registration Auto.Adj. (Refer to I.5.3.10 Color Registration
Auto.Adj. (Printer Adjustment))
- Color Registration Manual (Refer to I.5.3.11 Color Registration
Manual (Printer Adjustment))
Gamma Automatic Adjustment (Refer to I.5.4.7 Gamma
Automatic Adj. (Drum Peculiarity Adjustment))
- Beam Pitch Adjustment (Refer to I.5.3.14 Beam Pitch Adjustment
(Printer Adjustment))
- Moire Adjustment (Refer to I.5.3.15 Moire Adjustment (Printer
Adjustment))

mandatory adjustments after replacing developer...

- Counter reset of the parts counters No.41, 42 for the developer /
Y, No.43, 44 for /M, No.45, 46 for /C,and No.47, 48 for /K.
- Toner Density Sensor Init. (Refer to I.5.4.9 Toner Density Sensor
Init. (Drum Peculiarity Adjustment))
- Gamma Automatic Adjustment (Refer to I.5.4.7 Gamma
Automatic Adj. (Drum Peculiarity Adjustment))
Printer Gamma Offset Auto. (Refer to I.5.3.23 Printer Gamma
Offset Auto. (Quality Adjustment - Printer Gamma Adjustment))




mandatory adjustments after replacing drum(s)


After replacing the drum cartridge, conduct the following items.
- Cleaning the dust-proof glass (Refer to F.5.2.1 - Cleaning the
dust proof glass)
- Counter reset of the parts counter No.21, No.22 for drum
cartridge /Y, No.23, No.24 for drum unit /M, No.25, No.26 for drum
unit /C, No.27, No.28 for drum unit /K
- Color Registration Auto.Adj. (Refer to I.5.3.10 Color Registration
Auto.Adj. (Printer Adjustment))
- Color Registration Manual (Refer to I.5.3.11 Color Registration
Manual (Printer Adjustment))
- Gamma Automatic Adjustment (Refer to I.5.4.7 Gamma
Automatic Adj. (Drum Peculiarity Adjustment))

depending on the firmware there is a selection for running all drum peculiarity adjustments that goes from one screen to the next.
best to use that.

bad part is if you didnt run the toner density adjustment immediately after completely vacuuming out the units and refilling them all your adjustments will be for nothing.
these machines are really finicky if you don't follow the manual to the letter. any skipped or step out of order and its a waste of time and developer.

good luck!!

Dear Synthohol
Can you send me this manual? I realy need that.
my email:info@kabulpen.co

Thanks in advance

[Synthohol]

Re: Konica C6000: Gamma correction abnormality

i only share with people with a contributor badge. its not personal.
https://www.copytechnet.com/forums/v....php?do=donate

[Walterj]

Re: Konica C6000: Gamma correction abnormality

I replaced all new materials like drums, charging, develop, belt... PRCB, PRIPB, Image correction unit, Laser unit...

Good Day
Dear
I hope this contribution helps
I think you should check the HV boards
I imagine that you have reset the counters of the replaced inputs and made the adjustments according to the technical service manual


Regards