-
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^= -
Re: C224 Bizhub general maintenance
I did clean up the rollers and install back - just tested and the squeak's gone. Thanks rrrohan!
My second issue is to clean the DF tray and around since it's dusty and the Dust Off spray does not help. That's why I want to remove it so I can clean it separate from the printer.
Yes it have nothing to do with the squeak, which is fixed!Comment
-
Re: C224 Bizhub general maintenance
The reason that I'm discouraging you is that there is a wiring harness that runs through the real swivel post, through a series of looms to the DF controller. And as anal as I am, I have never removed a DF tray because of dust.
Just wipe it off and be happy.
You cannot submerge it. There are electronics inside. =^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: C224 Bizhub general maintenance
I have removed all the screws belong to the part 2 but cannot take it out now I just want to know how to remove the part 1 which is just piece of plastic, no electronic involved. It does not look difficult but I can figure it out how to do it.
IMG-9779.jpgComment
-
Re: C224 Bizhub general maintenance
There must be a dozen screws from the top, around the perimeter.
=^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: C224 Bizhub general maintenance
You don't think there's any electronics in the doc. feeder tray? How do you think it reads the size of the paper? I'd listen to blackcat if i were you or you may be starting another thread asking how to repair what you just broke. Just saying....Adversity temporarily visits a strong man but stays with the weak for a lifetime.Comment
-
Re: C224 Bizhub general maintenance
see those three slots in it? THOSE ARE SENSORS
Blackcat told you this..
just spray the tray lightly with organic cleaner.. wipe off .. go with it..
this is not rocket science man...
follow the K.I.S.S. principle
Keep It Simple Stupid.
if you remove it you are asking for major problems.Comment
-
Re: C224 Bizhub general maintenance
Agreed. This is one of those learning moments.
Some things its better to have good reason to remove. You can learn the easy way, or the hard way. Its up to you.If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: C224 Bizhub general maintenance
You'll want to clean it and reinstall it
Pull the shaft out, clean it. Don't lube it just clean
Blow out the rollers where shaft slides through
Clean any dried toner off rollers (if any)
Reassemble
Reinstall.
In regards to the DF don't waste time taking it apart. Nothing a paint brush, blower and some spray and wipe can't fix
Sent from my Pixel 4 XL using TapatalkComment
Comment