Increasing job priority does not stop current job

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Ornitorrinco Mordaz
    Technician
    • Nov 2024
    • 16
    #1

    Increasing job priority does not stop current job

    Good day everyone, does anybody know how to make it so that when you increase the priority of a given job, the current job stops and the printer starts printing the job with priority?

    I have a client with a bizhub 458, the client used to have a series 4 that did stop the current job for the one with the priority, we change his printer for this one but this one waits for the current job to finish and then prints the one with priority, some users sent jobs of hundreds of pages, so it was useful for the other ones not having to wait for smaller jobs

    Also if anyone has advice or tricks to make print jobs faster to load it would be useful, i already manage to change one setting that loads the PDFs faster in the printer, any similar advice even on the PC side would be helpful

    Thanks
    Tags: bizhub, job priority, konica, print, printer
    • blackcat4866
      Master Of The Obvious

      Site Contributor
      10,000+ Posts
      • Jul 2007
      • 22927
      #2
      Sounds very unlikely to me. Unless you specifically stop a job, it will finish.
      If you'd like a serious answer to your request:
      1) demonstrate that you've read the manual
      2) demonstrate that you made some attempt to fix it.
      3) if you're going to ask about jams include the jam code.
      4) if you're going to ask about an error code include the error code.
      5) You are the person onsite. Only you can make observations.

      blackcat: Master Of The Obvious =^..^=

        Comment

        • Synthohol
          Certified Konica Expert

          Site Contributor
          5,000+ Posts
          • Mar 2016
          • 5735
          #3
          if its in the middle of multiple sets you can hit interrupt and it will finish the set, then stop and allow other jobs.
          at least thats what i remember.
          and then pick up where it left off when returned unless its deleted (if allowed by admin)
          We know a thing or two because we've seen a thing or two.
          The medication helps though...
            👍 1

            Comment

            • tsbservice
              Field tech

              Site Contributor
              5,000+ Posts
              • May 2007
              • 7909
              #4
              Job interrupt should work fine at least it worked for this purpose back in analogue days.
              A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
              Blessed are they who can laugh at themselves, for they shall never cease to be amused.

                Comment

                • Ornitorrinco Mordaz
                  Technician
                  • Nov 2024
                  • 16
                  #5
                  I dont remember if this model has the job interrupt button, some panels has them other do not, they have the NFC instead:
                  ​ image.png ​​ image.png
                  Im going to check which one is, in case is the one with NFC, does it have an equivalent button?

                    Comment

                    • tsbservice
                      Field tech

                      Site Contributor
                      5,000+ Posts
                      • May 2007
                      • 7909
                      #6
                      Different machines C224e upper C258 lower but it has interrupt on touchscreen too.
                      A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
                      Blessed are they who can laugh at themselves, for they shall never cease to be amused.
                        👍 1

                        Comment

                        • femaster
                          Service Manager

                          1,000+ Posts
                          • May 2011
                          • 1458
                          #7
                          Originally posted by Ornitorrinco Mordaz
                          I dont remember if this model has the job interrupt button, some panels has them other do not, they have the NFC instead:

                          image.png
                          Im going to check which one is, in case is the one with NFC, does it have an equivalent button?
                          The machines with the NFC on the right edge of the control panel should have the interrupt "button" in the slide-out menu indicated by #9 in the following graphic. This menu should be accessible from any of the operation screens, including the Main Menu screen as shown below.

                          image.png​
                          A Ricoh Service Tech for 7 year. A Konica Minolta Service Tech for 7 years. Now, KM service manager for 4 years.
                          My Ricoh knowledge is slowly dwindling away at this point. Many things have been lost to time...
                            👍 1
                            😀 1

                            Comment

                            • JMS
                              Technician
                              • Apr 2023
                              • 19
                              #8
                              You can assign the interrupt-function to one of the four hard keys.
                              [Utility]
                              • [Administrator Settings]
                                • [System Settings]
                                  • [Registered Key Settings]
                                👍 1

                                Comment

                                Previous template Next
                                Working...