I have a C3070L with 55 version firmware and N2 @ 80 and I cannot find FOLD2, the instructions (see below) don't match the menu on the device either to get to the adjustment but tri-fold is there. Can anyone provide a bit of insight on this?
Instructions:
1. "Service Mode Menu screen"
Press [07 Finisher Adjustment].
2. "Finisher Adjustment Menu screen"
Press [01 Staple Finisher Adjustment].
3. "Staple Finisher Adjustment Menu screen"
Press [02 Staple Finisher(Fold) Adj.].
4. "Stapler(Fold) Adjustment Menu screen"
Press [06 Tri-Fold Adjustment].
5. "Tri-Fold Adjustment Menu screen"
Press [01 Tri-Fold Position Adjustment].
6. "Tri-Fold Position Adjustment screen"
Select the paper size that you want to adjust and press [Print Mode].
7. Load the paper which you want to adjust the size on the tray and press the Start key to output the test pattern (Number 16).
8. Check "a" and "b" on the outputted paper.
For details of standard values, refer to " I Table 1: Standard value."
9. When the value is not within the standard value, press [Exit PrintMode].
10. "Tri-Fold Position Adjustment screen"
Select the size of the paper that you want to adjust.
11. Press [Fold 1].
12. Enter a value through the numeric buttons and press [SET].
Setting range: -50 (longer) to +50 (shorter)
1 step = 0.1mm
• The dimension "a" in the step 7 gets larger when the setting data is moved to the positive side and gets smaller when it is moved to
the negative side.
13. Press [Fold 2].
14. Enter a value through the numeric buttons and press [SET].
Setting range: -50 (shorter) to +50 (longer)
1 step = 0.1mm
• The dimension "b" in the step 7 gets larger when the setting data is moved to the positive side and gets smaller when it is moved to
the negative side.
15. Repeat steps 6 to 14 until the standard value can be obtained.
Neither fold 1 nor fold 2 are visible as buttons on the trifold adj screen in service mode!
Thoughts?
Instructions:
1. "Service Mode Menu screen"
Press [07 Finisher Adjustment].
2. "Finisher Adjustment Menu screen"
Press [01 Staple Finisher Adjustment].
3. "Staple Finisher Adjustment Menu screen"
Press [02 Staple Finisher(Fold) Adj.].
4. "Stapler(Fold) Adjustment Menu screen"
Press [06 Tri-Fold Adjustment].
5. "Tri-Fold Adjustment Menu screen"
Press [01 Tri-Fold Position Adjustment].
6. "Tri-Fold Position Adjustment screen"
Select the paper size that you want to adjust and press [Print Mode].
7. Load the paper which you want to adjust the size on the tray and press the Start key to output the test pattern (Number 16).
8. Check "a" and "b" on the outputted paper.
For details of standard values, refer to " I Table 1: Standard value."
9. When the value is not within the standard value, press [Exit PrintMode].
10. "Tri-Fold Position Adjustment screen"
Select the size of the paper that you want to adjust.
11. Press [Fold 1].
12. Enter a value through the numeric buttons and press [SET].
Setting range: -50 (longer) to +50 (shorter)
1 step = 0.1mm
• The dimension "a" in the step 7 gets larger when the setting data is moved to the positive side and gets smaller when it is moved to
the negative side.
13. Press [Fold 2].
14. Enter a value through the numeric buttons and press [SET].
Setting range: -50 (shorter) to +50 (longer)
1 step = 0.1mm
• The dimension "b" in the step 7 gets larger when the setting data is moved to the positive side and gets smaller when it is moved to
the negative side.
15. Repeat steps 6 to 14 until the standard value can be obtained.
Neither fold 1 nor fold 2 are visible as buttons on the trifold adj screen in service mode!
Thoughts?
Comment