This has been happening close to a week now. No matter 11x17. Letter, 12x18 no matter orientations either just paper jam in the fuser20220509_155254.jpg
Sent from my SM-G780G using Tapatalk
Sent from my SM-G780G using Tapatalk
-
-
Re: C454e constantly jamming
Fuser clutch CL8 ? -
Re: C454e constantly jamming
Jam code please.
Looks like exit clutchA tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Re: C454e constantly jamming
This is the error code20220509_173018.jpg
Sent from my SM-G780G using TapatalkComment
-
Re: C454e constantly jamming
Next this is this
I changed all the drums the ibt belt and blade and I'm Stull getting prints with this issue. Please check the top
See how it's lighter to the top of the print
Sent from my SM-G780G using TapatalkComment
-
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Re: C454e constantly jamming
Posting CMYK halftones helps so much to identify problems.
The sensor flags can get worn out if the machine has a high reading. At about 1.3M things wear out.
J-9202 I think is for the clutch.
Then J-3205 if the pads that dampen noise on the gate goes sticky or if the sensor actuator on the duplex entrance on the door gets misformed by heat for the fuser.WhateverComment
-
A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Re: C454e constantly jamming
You will find all that in service manual and parts list... IMHO working on machine without them is a waste of time.
As far for asking about image formation problems pay attention what allan wrote, we need those patterns for better troubleshooting and it takes like 5 minutes to print them.A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
Blessed are they who can laugh at themselves, for they shall never cease to be amused.Comment
-
Re: C454e constantly jamming
Some halftone pages would be a great help here, but since you are also struggling with a jamming issue, get that resolved and then get the halftones. While the fade issue you are seeing can be caused by any number of issues, there are a few that can be the result of a dirty PH (Print Head) unit, also know as the laser unit in some circles.
Not sure what you've tried so far to remedy the fading, but the first step should be to try and clean the laser glass. There should be a cleaning wand attached to the inside front access door of the copier. Another possibility involving the laser unit is dust on the mirror motor inside the unit. On the Cxx4e models, the polygon mirror motor sometimes collects a layer of dust on the tips (corners) of the mirrors that write to the top (rear) edge of the drums resulting in a lighter, faded looking image. Fixing this requires removing the laser unit from the copier and carefully dismantling it, removing the mirror motor and very carefully cleaning off the mirror surfaces. Looking closely at the corners, the dust should be obvious if that is what's causing your problem.A Ricoh Service Tech for 7 year. A Konica Minolta Service Tech for 7 years. Now, KM service manager for 4 years.
My Ricoh knowledge is slowly dwindling away at this point. Many things have been lost to time...Comment
Comment