I have 3 models of Kyocera km 3035-km5035 and I have a problem when I tried to configure the scan mode. I entered the correct password and then pushed the next button "basic configuration" but it comes a label "unable scan". I have tried to return to the basic configuration, wait aprox. 2 min but nothing happened. Can somebody help me? Thanks. Samuel
-
-
Re: how configurate the scan???? KM 3035,4035,5035??????
You need to have a network cable plugged into the scanner board.
Unlike the printer settings, you must be connected in order to access the scanner configuration.
Or, if you are new to kyocera you might not realize that printing and scanning are transmitted through two separate NIC cards. -
If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
i want cofigurate TWAIN and Email Scan tks.Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
I hope I didn't upset you by asking exactly what you wanted.
Well, I really don't care that much. =^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
OK,
Firstly, make sure that you have a network cable connected to the scan card.
Secondly, assign an IP address to the scan card (open/unused address different than the print card).
Thirdly, Access the web interface to enter: SMTP information, default sender address, any addressbook entries.
Fourth, Load the TWAIN utility to the server or any PCs you intend to run the TWAIN application from:
Look here:
The TASKalfa 305/255 can dramatically lower your TCO total cost of ownership...Kyocera's SMARTtech is affordable
If you need a Spanish language utility, you'll need to find that yourself (my Spanish is not good enough to find my way through the menus):
Is this it?:
Kyocera Color Laser Printer Copier Scanner Fax MFP Products
Once loaded, the TWAIN utility will need to be configured to find the scanner.
Enjoy! =^..^=If you'd like a serious answer to your request:
1) demonstrate that you've read the manual
2) demonstrate that you made some attempt to fix it.
3) if you're going to ask about jams include the jam code.
4) if you're going to ask about an error code include the error code.
5) You are the person onsite. Only you can make observations.
blackcat: Master Of The Obvious =^..^=Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
Strange way to ask for help.Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
Are you asking for scan to email, folder (and or SMB?) Let me know. RussComment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
yes i want cofigarate the scan to the email (smtp) and to folder. tks.Comment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
Hi! try this link maybe you can get something. A lot of our good friends here helped me on the same problem
http://www.copytechnet.com/forums/ky...p-scanner.htmlComment
-
Re: how configurate the scan???? KM 3035,4035,5035??????
OK lets start. I assume that you can get on a browser page from the IP of the scanner correct? If so look on the left side for you email settings. You will need your SMTP host name or IP address. (try the address first, sometimes you need smtp.xxx. sometimes not) Check the port, as default is 25. If your SMTP server is an exchange this should be all you need for this part. You may not need a login name and password if the exchange is not relaying out the LAN. If your SMTP requires SSL, you should stop here. Scanner card wont work with SSL. After your register on the bottom, look on the left again and add your name and email address under sender. Register. Look on the left and add your name and email again under email address. That should get you close. If you get an error under history on control panel, let me know. Scan to folder work well also if you want. Will need a program called scanner file. I can send to you. Please send a private message to me and I can send that ( 4 megs or so, and a screen shot on how to configure it that i made up). RussComment
Comment