[Dead] Ricoh MP C4500 Shadow when printin or copying

[feroo666]

After changing the ink when printing or copying out the picture under her often be double yellow and Writing (duplicate) like the picture attached Help me because maintenance engineers are asking for a huge sum of money seized

i think i can solve it from the SP But I do not know how it's done

[skynetto]

Re: Ricoh MP C4500 Shadow when printin or copying

You either invest yourself in a service manual or hire a tech to solve your problems. In the service manual you'll find the procedure for laser calibration and all the other questions you have placed around the forum. Anyway check the 2-111 section for forced manual calibration.

[feroo666]

Re: Ricoh MP C4500 Shadow when printin or copying

i will try thanks

[feroo666]

Re: Ricoh MP C4500 Shadow when printin or copying

You either invest yourself in a service manual or hire a tech to solve your problems. In the service manual you'll find the procedure for laser calibration and all the other questions you have placed around the forum. Anyway check the 2-111 section for forced manual calibration.

I tried but appeared message Faild

[skynetto]

Re: Ricoh MP C4500 Shadow when printin or copying

Check ITB status. If worn the pattern calibration would fail. Check ID sensor status. If dirty it would fail as well. Check black developer if out of life. The machine checks the other color in corrispindence of the black one. Clean laser window and remove laser shutter if present.
After all these checks reset calibration setting as per procedure
Copy SP: 5610-4
Printet SP: 1101-1
Copy SP: 3011-1
Check results in 3012-1
If all 1 begin forced laser allignment
2111-3 once and 2111-1 twice.
Check alignment with Printer SP
1103-2

If in the above step the results of 3012-1 are not all 1 check the remedy in the service manual.

[feroo666]

Re: Ricoh MP C4500 Shadow when printin or copying

You either invest yourself in a service manual or hire a tech to solve your problems. In the service manual you'll find the procedure for laser calibration and all the other questions you have placed around the forum. Anyway check the 2-111 section for forced manual calibration.

Check ITB status. If worn the pattern calibration would fail. Check ID sensor status. If dirty it would fail as well. Check black developer if out of life. The machine checks the other color in corrispindence of the black one. Clean laser window and remove laser shutter if present.
After all these checks reset calibration setting as per procedure
Copy SP: 5610-4
Printet SP: 1101-1
Copy SP: 3011-1
Check results in 3012-1
If all 1 begin forced laser allignment
2111-3 once and 2111-1 twice.
Check alignment with Printer SP
1103-2

If in the above step the results of 3012-1 are not all 1 check the remedy in the service manual.

Followed all the steps but still gives an error message when I Check results in 3012-1 I see the counter 11111159

then i see error message again faild

[skynetto]

Re: Ricoh MP C4500 Shadow when printin or copying

Error 59: Insufficient data for gamma correction. Check Black Developer status and ID sensor status.

So you haven't done what I've told you to do.

Conslusion: Buy a manual or hire a tech.

[ali.alhaj]

Re: Ricoh MP C4500 Shadow when printin or copying

Dear
Find the sp paper in front door and filling the parameters and do 2111 line position c,b,a not a,b,c

[Oze]

Re: Ricoh MP C4500 Shadow when printin or copying

PAY FOR A SERVICE...OR GO TO FIXYA.COM AND ASK YOUR QUESTIONS.......oh....and Happy New Year!!!!!!

[slimslob]

Re: Ricoh MP C4500 Shadow when printin or copying

Followed all the steps but still gives an error message when I Check results in 3012-1 I see the counter 11111159

then i see error message again faild

Error 59: Insufficient data for gamma correction. Check Black Developer status and ID sensor status.

So you haven't done what I've told you to do.

Conslusion: Buy a manual or hire a tech.

You most likely need to replace the image density sensor, the black drum unit and the black development unit.

[Oze]

Re: Ricoh MP C4500 Shadow when printin or copying

You most likely need to replace the image density sensor, the black drum unit and the black development unit.

He can't do that Slim because...and I quote:

Help me because maintenance engineers are asking for a huge sum of money seized

Bastard techs..trying to make a living and all

[bob marley]

[turbojetboy]

Re: Ricoh MP C4500 Shadow when printin or copying

My guess is the machine has had a very recent memory clear, as the colour reg always goes out the window ( with a lot of other things) after a mem clear.

[slimslob]

Re: Ricoh MP C4500 Shadow when printin or copying

I had a machine a couple of years ago, either a MP C4501 or C4502, that kept going out of color registration. Ran ACC and it pulled it back. Two days later, out of registration again. Cleaned ID sensor and ran ACC. A week and a half later, out of registration again. As it was less than 3 months old, regional rep came out and brought an ITB unit with him. Problem solved. It seems that the ITB belt will sometimes start slipping.