Altalink 80XX Series special Altboot method

[katapablo]

This is it 20210506_160337_1620310087654.jpg

It's a "U." with a blinking dot

But when the machine's restart makes a :" 8 , 1 , 4 , 0 , 5 , 9 , u. "

[adriansto]

This is it 20210506_160337_1620310087654.jpg

[katapablo]

What is the code on the small 7 digit display?
Can be the SD card corruption, hdd system software corruption or bad hdd.
Did you tried to reseat the sd card and hdd connectors?

I don't understand what do you mean the small 7 digit display, you mean in the screen during the resets? Or the number led that have in the connection area?

About the HDD and the card, we have tested in another working machines, and both works good.
I switch the HDD and the SDcard for the non-working machine to a working machine, same model(but different motherboard) and works good.


Thanks for your fast asnwer!!

[adriansto]

What is the code on the small 7 digit display?
Can be the SD card corruption, hdd system software corruption or bad hdd.
Did you tried to reseat the sd card and hdd connectors?

[katapablo]

Good morning, I have a Xerox Altalink C8035, that doesn't start, I think that it is a firmware problem, I have read everything you say, but it is not clear to me what I have to do, what version to reinstall.

I add some pictures to try to help, the version that the machines suppose to have is 100.001.057.09609.

Here you have a video to see what happens, I mean restart, restart and restart again.

https://youtu.be/sEHUn8lFXSo

If you can let me know what can I do to solve it please.

Regards

[hnami]

hi
i found 81xx series firmwares in site https://specialaltboot.com/products/
if anyone download this firmwares please share in forum
thanks

[hnami]

Hi, I have a problem with my C8035. I need sd card firmware but I can not find it. Can you please send me a link?

Yes.pm me hamednami1361@gmail.com

[AhmetSRN]

What’s your problem?

Hi, I have a problem with my C8035. I need sd card firmware but I can not find it. Can you please send me a link?

[REC17]

I formatted my HDD and SD card then reinstalled the image from a working HDD and SD card using the Active disk image software. I insert my flash drive inside the C8045 machine front USB panel, but it does not install the firmware. I have uploaded what is in my flash drive altboot file and the screen display to this message. I have also used the SD-image card that was put on this platform but still get the same screen display. I get the same screen display for both the C8045 and C8070, for the C8070 HDD i used the HDD image for the C8045 and the SD image from this platform i downloaded.

[hnami]

Hello guys i am having a similar issue with my C8045 and C8070, can i just continue or do i need to open a new post

What’s your problem?

[REC17]

Hello guys i am having a similar issue with my C8045 and C8070, can i just continue or do i need to open a new post

[hnami]

Thank you Hnami. I put in new hard drive and SD card, loaded v101.xxx firmware with swup files and the machine is alive again
Could not have done it without you, much appreciated.

Please. It needs some experience😉

[Dougtech]

Thank you Hnami. I put in new hard drive and SD card, loaded v101.xxx firmware with swup files and the machine is alive again
Could not have done it without you, much appreciated.

[hnami]

Altalink C8070 Unable to decrypt DLM
The Issue I started with the unable to decrypt DLM, Using the files from this thread and from Detonation , I was able to see the "Decrypting" screen and then the install screen. After removing the USB and reboot, the machine continues to boot loop. I've upload a photo of the install screen.

The original issue was the SBC went bad and I replaced and installed the SD and HDD from the original SBC.

My thought is that according to hnami , the swup_usb file on this thread is 81KB and should be 83kb. Since I was able to see the install screen, I'm wondering if I need the 83kb file?
The POST indicator light is a lowercase n. I can't find any documentation for "n"

If you fall on boot loop after installing screen show and restart your data can’t store on hdd drive.try change hdd first

[hnami]

Altalink C8070 Unable to decrypt DLM
The Issue I started with the unable to decrypt DLM, Using the files from this thread and from Detonation , I was able to see the "Decrypting" screen and then the install screen. After removing the USB and reboot, the machine continues to boot loop. I've upload a photo of the install screen.

The original issue was the SBC went bad and I replaced and installed the SD and HDD from the original SBC.

My thought is that according to hnami , the swup_usb file on this thread is 81KB and should be 83kb. Since I was able to see the install screen, I'm wondering if I need the 83kb file?
The POST indicator light is a lowercase n. I can't find any documentation for "n"

Along with the swup_usb file, another file called swup_c8045-55 must be available. You need these two files