C284e error c-e004

[Synthohol]

Re: C284e error c-e004

I don't think 284s come with a hdd. So all scans and data go through the ssd instead..

[oscar]

Re: C284e error c-e004

Ok i have been able to solve this code with out having to replace MFP board.
I formatted the SSD both logical and physical (doesnt take long at all),once the machine rebooted itself after the physical format the machine gave a hard drive error,did a logical format only. I rebooted and then got a fax error so then initilized fax,rebooted and happy days the machine came back up error free.

how did you format the logical and physical SSD?

[Brett GS]

Re: C284e error c-e004

Ok i have been able to solve this code with out having to replace MFP board.
I formatted the SSD both logical and physical (doesnt take long at all),once the machine rebooted itself after the physical format the machine gave a hard drive error,did a logical format only. I rebooted and then got a fax error so then initilized fax,rebooted and happy days the machine came back up error free.

[Woxner]

Re: C284e error c-e004

yes there is a procedure you must follow. you have to enter machine type when replacing mfp. put firmware on usb then put in service port.turn on machine but do not install firmware at this time.enter machine type when it comes up after machine type is put in turn machine off wait 20seconds then back on then let it do firmware

[Brett GS]

Re: C284e error c-e004

Hi guys
Anymore solutions for this code??
Got a C284e giving same code.
The machine accepts firmware fine but when it boots up i get the copy screen and about a 1 min later the code comes back,tried system error clear,reseating mfp connectors and ribbon cables,formatted HDD and even unset it in service mode but no joy at all.

[allan]

Re: C284e error c-e004

Yes its a licensing this to start with. Data for this machine is located on all the prints.
The data gets read back from the existing prints to the replaced ones.
Its a triangular @#$%.


I get the idea that you need a licence key for the machine to come right.

[barber782]

Re: C284e error c-e004

New board didn't work!!

[barber782]

Re: C284e error c-e004

Any particular procedures when replacing mfp board?

[Grey]

Re: C284e error c-e004

Had this same code c-e004 on a Bizhub 454e with paper behind the trays.

Machine would reset, come to ready state, and then code out again in about 2 minutes.

Took it off of the network, same result.

After the standard run around with a ticket to SSD, ordered a MFP board.

New board did the trick.

Great to know that paper behind the drawers will cause a static blow out to the MFP.

[blackcat4866]

Re: C284e error c-e004

system error reset = trouble reset
=^..^=

[andyf424]

Re: C284e error c-e004

I did a system error clear in service mode and no good. How do you go about doing a trouble reset on these? I remember on the older models you hold down utility counter button on boot up.

reset key on newer machines.

[barber782]

Re: C284e error c-e004

Reseated dimms aswell and no joy. Will check out those electronic checks .

[barber782]

Re: C284e error c-e004

I did a system error clear in service mode and no good. How do you go about doing a trouble reset on these? I remember on the older models you hold down utility counter button on boot up.

[Mr Spock]

Re: C284e error c-e004

Try a trouble reset. I have had several that after customer turned off and on several times did not clear with out a trouble reset.

[copier tech]

Re: C284e error c-e004

Did you try to SET/UNSET tray one in SE mode?