BIZHUB C554e error after been deconencted from the main supply

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

Oke, I have took of the fuse, cleaned inside and there is no sound anymore.. I suppose it's will not be for a long time !!
I do understand where I have to look about the "oil roller and holder" if someone have a picture I will be grateful if it's can be shared.

How I can change the title of the thread to add resolved ?

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

thanks for your advice,
I will check that and keep you in touch. Not sure that will be today but it's will be on the week.

[Synthohol]

Re: BIZHUB C554e error after been deconencted from the main supply

That's the oil roller bushings.
Remove the 2 side and front cover and you can remove the oil roller and holder.
One or 2 c clip and its out. No more noise.

[femaster]

Re: BIZHUB C554e error after been disconnected from the main supply

I don't know why the upload isn't working.

here the file by wetransfer
https://we.tl/t-cxF7gsCVDg

With it sitting idle like that and squeaking, you are looking at the fuser and/or the drive unit for the fuser. You might be able to get away with lightly oiling the bearings / bushings in both, but with it that loud, your may be looking at the need to replace parts. Power down the machine and remove the fuser. Locate the large drive gear on the right side of the fuser and spin it by hand and see if you can hear any squeaking. If yes, start there. If no, look to the gear box that drives the fuser. Noises are always fun!

[handixx]

Re: BIZHUB C554e error after been disconnected from the main supply

please record the noise on your phone and post it here.

I don't know why the upload isn't working.

here the file by wetransfer

https://we.tl/t-cxF7gsCVDg

[Synthohol]

Re: BIZHUB C554e error after been disconnected from the main supply

please record the noise on your phone and post it here.

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

tar file on the root and its installed in install data in service mode, system input install data.

ALL GOOD !! the machine work like before the main supply issue !!!! THANKS A LOT !!

do you have a glue to gave me for the noise ?

[Synthohol]

Re: BIZHUB C554e error after been deconencted from the main supply

tar file on the root and its installed in install data in service mode, system input install data.

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

i dont think you can disable life stop after they go over it had to be done prior. now it has forgotten it was ignoring life limits you now have no choice to replace them or re chip them. unfortunate side effect to the original fault

it's work you can disable

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

I bet my money on stopped print or similar.

the problem wasn't there, it's was a misunderstood about the enable thing

[handixx]

Re: BIZHUB C554e error after been deconencted from the main supply

when i said make sure everything is enabled in problem unit isolation, i didnt mean set them all to be isolated.
konica has a way of saying things in reverse like when you want to disable sleep mode you go to sleep on/off setting and the choice is permit or not permit so you would think not permit means you dont want to permit it to sleep. this is not the case. it is to permit or not the display of being able to select do not sleep in admin mode. crazy right?
i see how you assumed set or unset means the opposite of what i was asking to check.
i hope its all straightened out.
did you check the life stop setting and set it to do not stop?
you may get lucky.

I didn't get it !! so yes now it's better when nothing is enable .
I have the pleasure to tell you that : I made a copy !!

just la last error, the animation staff... when I made the upgrade i din't put the .tar because I didn't knew where I have to put it.
how it's work ? I put it on the root and boot on the usb ?

and the cherry on the cake, when the machine is powered, i mean not in low power mode setting I hear a "oiiiiiii oiiiiii oiiiii". where should I inspect to know which moving part I have to replace ?

[rrrohan]

Re: BIZHUB C554e error after been deconencted from the main supply

i dont think you can disable life stop after they go over it had to be done prior. now it has forgotten it was ignoring life limits you now have no choice to replace them or re chip them. unfortunate side effect to the original fault

[tsbservice]

Re: BIZHUB C554e error after been deconencted from the main supply

Hi, all done,

look like working again !! I have just a alarm asking me to replace all my drum unit..
Can we reset that , because they are almost new ><

Seems they are not is where you lost me...duhh Frenchmans are so good in cooking for others but nothing more.

[Synthohol]

Re: BIZHUB C554e error after been deconencted from the main supply

when i said make sure everything is enabled in problem unit isolation, i didnt mean set them all to be isolated.
konica has a way of saying things in reverse like when you want to disable sleep mode you go to sleep on/off setting and the choice is permit or not permit so you would think not permit means you dont want to permit it to sleep. this is not the case. it is to permit or not the display of being able to select do not sleep in admin mode. crazy right?
i see how you assumed set or unset means the opposite of what i was asking to check.
i hope its all straightened out.
did you check the life stop setting and set it to do not stop?
you may get lucky.

[tsbservice]

Re: BIZHUB C554e error after been deconencted from the main supply

If you press job list, go into the job log, highlight a failed job and press details.

This should give you a clue as to why the job failed.

I bet my money on stopped print or similar.