AK-7110 Jamming

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • toddanderson
    Trusted Tech
    100+ Posts
    • Dec 2005
    • 214

    AK-7110 Jamming

  • KYO_OEM
    Senior Tech
    500+ Posts
    • Aug 2011
    • 618

    #2
    Re: AK-7110 Jamming

    Which jam code do you get?

    Comment

    • Tonerkiller
      Senior Tech
      500+ Posts
      • Oct 2012
      • 656

      #3
      Re: AK-7110 Jamming

      In the setup instructions there is a procedure for tightening the screws. I would start there. How about the fuser? Is it getting hard to turn?

      Comment

      • toddanderson
        Trusted Tech
        100+ Posts
        • Dec 2005
        • 214

        #4
        Re: AK-7110 Jamming

        J6101 on 11x17.
        It will jam from any cassette, or mp tray
        I have also replaced the fuser, only about 50k copies o machine. I have seen the same issue on different machine. but most customers dont run 11x17
        or run very little.


        Originally posted by KYO_OEM
        Which jam code do you get?

        Comment

        • ihatefinishers13
          Senior MFP Technician
          250+ Posts
          • Feb 2020
          • 326

          #5
          Re: AK-7110 Jamming

          Originally posted by toddanderson
          J6101 on 11x17.
          It will jam from any cassette, or mp tray
          I have also replaced the fuser, only about 50k copies o machine. I have seen the same issue on different machine. but most customers dont run 11x17
          or run very little.
          When you said you shimmed the paper pass unit, was that to push it tighter together? I would inspect that whole unit and check to see if anything has deformed or cracked, even a tiny one can cause issues. Also see if you can pass paper through it when it's out of the unit by turning the rollers by hand - but NOT putting pressure on them; to see if the rollers have enough pressure between them to pass the paper on their own.

          Comment

          • Rpizzle
            Technician
            • Mar 2014
            • 41

            #6
            Re: AK-7110 Jamming

            How about checking if the paper stack limit plastic piece is still on the exit flag?

            I have not seen this on any of these units, with such a low count I have a hard time believing there is something broken.

            Keep us posted!

            Comment

            • KYO_OEM
              Senior Tech
              500+ Posts
              • Aug 2011
              • 618

              #7
              Re: AK-7110 Jamming

              @toddanderson
              seems to be a firmware problem from system if AK would installed on 4054ci.
              Found similar case regarding J6101 only in case of 11x17 on several systems.
              Set to thick/ heavy 1 solved the problem, but speed decreased for plain.
              Finally change from exit motor speed fixed it.

              J6101.JPG

              Comment

              • fishleg
                Trusted Tech
                Site Contributor
                250+ Posts
                • Mar 2009
                • 410

                #8
                Re: AK-7110 Jamming

                Originally posted by KYO_OEM
                @toddanderson
                seems to be a firmware problem from system if AK would installed on 4054ci.
                Found similar case regarding J6101 only in case of 11x17 on several systems.
                Set to thick/ heavy 1 solved the problem, but speed decreased for plain.
                Finally change from exit motor speed fixed it.

                [ATTACH=CONFIG]61401[/ATTACH]
                Curious what mode is that? Interesting you'd think that would through all the timing out.

                Comment

                • nathicana
                  Trusted Tech
                  Site Contributor
                  250+ Posts
                  • Aug 2008
                  • 304

                  #9
                  Re: AK-7110 Jamming

                  Any definite solution to this AK-7110 jamming problem on 11 x 17?

                  I'm getting j4918, j4912 bridge conveying sensor 1 stay jam only on 11 x 17 with paper stalled about to exit AK-7110

                  I'm looking into the exit motor speed.

                  Comment

                  • nathicana
                    Trusted Tech
                    Site Contributor
                    250+ Posts
                    • Aug 2008
                    • 304

                    #10
                    Re: AK-7110 Jamming

                    Thanks KYO_OEM, I adjusted exit motor speed to -3500 in u053 motor 3 as shown above.

                    The 11 x 17 jamming problem seems to be resolved.

                    Could this adjustment also help cure 500x non arrival jams in the AK-7110?

                    Comment

                    • KYO_OEM
                      Senior Tech
                      500+ Posts
                      • Aug 2011
                      • 618

                      #11
                      Re: AK-7110 Jamming

                      i don`t think so, but i would take care for the oneway pulleys #36 for the driving belts and the belts #37+38 itself.
                      J500x.JPG
                      Attached Files

                      Comment

                      Working...