SHarp MX2700

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Larhal
    Semi Retired

    Site Contributor
    VIP Subscriber
    500+ Posts
    • May 2013
    • 532
    #1

    [CQ] SHarp MX2700

    We received in a used MX 2700 in.

    This is new to me. I have the service manual. The unit was printing light in all colours when doing test patterns. When printing Black it is dense, only in full colour prints it is light. Copied light also.

    I changed Dev units, Drum units transfer belt and did all the prescribed setups as per the manual. Still have the same problems. It also won't read the chart from the colour balance auto adjust.

    Look we are not a Sharp dealer but a small Ricoh service group. Yes Ricoh trained.

    Any Ideas where I should go to get this correct?

    All input would be appreciated.

    Thanks,

    Larhal
    Larhal

    Retired Part Time

    If all else fails read the Service Manual!

    If that fails, meet me at the pub and we will discuss it.
    Tags: None
    • harleyrider
      Trusted Tech

      250+ Posts
      • Oct 2011
      • 348
      #2
      Re: SHarp MX2700

      Too many things to mention. What simulations did you use and or reset so far?

        Comment

        • mojorolla
          The Wolf

          2,500+ Posts
          • Jan 2010
          • 2569
          #3
          Re: SHarp MX2700

          On this model, check the LSU shutters are opening all the way.
          It probably is failing when scanning the charts because the image is too light.


          Failing to plan is planning to fail!!!

            Comment

            • Larhal
              Semi Retired

              Site Contributor
              VIP Subscriber
              500+ Posts
              • May 2013
              • 532
              #4
              Re: SHarp MX2700

              Hi all,

              1- LSU shutter is OK, checked that.

              Simulations used are as follow
              55-22
              46-24
              26-53
              67-24
              24-4
              24-7

              Kind of lost here do not know Sharp's.

              Larhal
              Larhal

              Retired Part Time

              If all else fails read the Service Manual!

              If that fails, meet me at the pub and we will discuss it.

                Comment

                • faxman28
                  Trusted Tech

                  Site Contributor
                  250+ Posts
                  • Nov 2010
                  • 436
                  #5
                  Re: SHarp MX2700

                  follow this procedure in attached bulletin, also do you have samples.
                  Attached Files

                    Comment

                    • harleyrider
                      Trusted Tech

                      250+ Posts
                      • Oct 2011
                      • 348
                      #6
                      Re: SHarp MX2700

                      I don't see 25-2. Follow the above bulletin.

                        Comment

                        • blackcat4866
                          Master Of The Obvious

                          Site Contributor
                          10,000+ Posts
                          • Jul 2007
                          • 22927
                          #7
                          Re: SHarp MX2700

                          I don't see the developer stir in there: simulation 25-02. This is an important one.
                          Then re-do the calibration. =^..^=
                          If you'd like a serious answer to your request:
                          1) demonstrate that you've read the manual
                          2) demonstrate that you made some attempt to fix it.
                          3) if you're going to ask about jams include the jam code.
                          4) if you're going to ask about an error code include the error code.
                          5) You are the person onsite. Only you can make observations.

                          blackcat: Master Of The Obvious =^..^=

                            Comment

                            • Larhal
                              Semi Retired

                              Site Contributor
                              VIP Subscriber
                              500+ Posts
                              • May 2013
                              • 532
                              #8
                              Re: SHarp MX2700

                              I printed out the Tech bulletin and will follow this verbatim, Also I will do the developer stir, I will advise of my results.

                              Thank all for your contributions of knowledge.

                              Larhal
                              Larhal

                              Retired Part Time

                              If all else fails read the Service Manual!

                              If that fails, meet me at the pub and we will discuss it.

                                Comment

                                • Larhal
                                  Semi Retired

                                  Site Contributor
                                  VIP Subscriber
                                  500+ Posts
                                  • May 2013
                                  • 532
                                  #9
                                  Re: SHarp MX2700

                                  Hi All,

                                  I performed the required items on the service bulletin and low and behold, its alive again.


                                  Want to thank you for your contributions , Great help.

                                  Best regards,

                                  Larhal
                                  Larhal

                                  Retired Part Time

                                  If all else fails read the Service Manual!

                                  If that fails, meet me at the pub and we will discuss it.

                                    Comment

                                    • blackcat4866
                                      Master Of The Obvious

                                      Site Contributor
                                      10,000+ Posts
                                      • Jul 2007
                                      • 22927
                                      #10
                                      Re: SHarp MX2700

                                      You're welcome. =^..^=
                                      If you'd like a serious answer to your request:
                                      1) demonstrate that you've read the manual
                                      2) demonstrate that you made some attempt to fix it.
                                      3) if you're going to ask about jams include the jam code.
                                      4) if you're going to ask about an error code include the error code.
                                      5) You are the person onsite. Only you can make observations.

                                      blackcat: Master Of The Obvious =^..^=

                                        Comment

                                        • harleyrider
                                          Trusted Tech

                                          250+ Posts
                                          • Oct 2011
                                          • 348
                                          #11
                                          Re: SHarp MX2700

                                          no problem

                                            Comment

                                            Previous template Next
                                            Working...