Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20
  1. #11
    Senior Tech 2,500+ Posts
    mpc3003 offset (ghost image) after sleeve unit replaced

    mikadonovan's Avatar
    Join Date
    May 2008
    Location
    Indianapolis, Indiana
    Posts
    2,662
    Rep Power
    79

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Did you perform the procedures listed in tech bulletin 30 as MGA suggested? It specifically addresses this issue.
    NEVER ASSUME ANYTHING

  2. #12
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,397
    Rep Power
    38

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by mikadonovan View Post
    Did you perform the procedures listed in tech bulletin 30 as MGA suggested? It specifically addresses this issue.
    Sorry, forgotten to mention.
    Yes i did, no good.
    Just 5 minutes ago a customer complained (again) for smear.
    I have refurbished the F.U. with a new sleeve and new PR.
    No good!
    Firmware is up to date.
    Medium thick seems to be the only solution so far.
    Do you encounter the same problem?

  3. #13
    Service Manager 1,000+ Posts
    mpc3003 offset (ghost image) after sleeve unit replaced


    Join Date
    Nov 2007
    Location
    New Jersey
    Posts
    1,144
    Rep Power
    62

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by Mark Bbb View Post
    Sorry, forgotten to mention.
    Yes i did, no good.
    Just 5 minutes ago a customer complained (again) for smear.
    I have refurbished the F.U. with a new sleeve and new PR.
    No good!
    Firmware is up to date.
    Medium thick seems to be the only solution so far.
    Do you encounter the same problem?

    Can you go into service mode and find the fuser settings for the different types of paper? Just take the settings for medium thick and apply them to plain paper.

  4. #14
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,397
    Rep Power
    38

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by anothertech View Post
    Can you go into service mode and find the fuser settings for the different types of paper? Just take the settings for medium thick and apply them to plain paper.
    I tried to find this info in the serv man, i can't find it.
    How do you cope with this problem?

  5. #15
    Field Supervisor 500+ Posts
    Join Date
    Oct 2011
    Location
    Hunter Valley, NSW
    Posts
    820
    Rep Power
    43

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by Mark Bbb View Post
    I tried to find this info in the serv man, i can't find it.
    How do you cope with this problem?
    Get a better manual. SP 1105

  6. #16
    Service Manager 1,000+ Posts Gift's Avatar
    Join Date
    Mar 2011
    Location
    Gothenburg
    Posts
    1,000
    Rep Power
    35

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    We also have this every now and then - some sorts of paper/enviroments aren't running well without a little "temp boost". I think normal paper setting is used to a maximum of 81g/m2 - not much of a margin there to compensate for poor paper. If the customer is using color copy paper 90g/m2 you shuld set it on medium anyways

  7. #17
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,397
    Rep Power
    38

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by anothertech View Post
    Can you go into service mode and find the fuser settings for the different types of paper? Just take the settings for medium thick and apply them to plain paper.
    These settings i have put in plain paper. Although it is better, it is no solution. Notice that M-thick FC center is going to low speed; how should i set that up???
    So, "Medium thick" seems to be the only solution. I do not understand why Ricoh don't take any steps. And i do not understand why i'm the only one that seems to have this problem?

    014 M-thick:FC:Press *ENG [0 to 200 / 120 / 1 deg/step]
    015 M-thick:BW:Center *ENG [100 to 180 / 150 / 1 deg/step]
    016 M-thick:BW:Press *ENG [0 to 200 / 120 / 1 deg/step]

    109 M-thick:FC:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
    110 M-thick:FC:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]
    111 M-thick:BW:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
    112 M-thick:BW:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]

  8. #18
    Copier Technician 1,000+ Posts
    mpc3003 offset (ghost image) after sleeve unit replaced

    mga's Avatar
    Join Date
    Dec 2010
    Location
    london
    Posts
    1,184
    Rep Power
    114

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by Mark Bbb View Post
    These settings i have put in plain paper. Although it is better, it is no solution. Notice that M-thick FC center is going to low speed; how should i set that up???
    So, "Medium thick" seems to be the only solution. I do not understand why Ricoh don't take any steps. And i do not understand why i'm the only one that seems to have this problem?

    014 M-thick:FC:Press *ENG [0 to 200 / 120 / 1 deg/step]
    015 M-thick:BW:Center *ENG [100 to 180 / 150 / 1 deg/step]
    016 M-thick:BW:Press *ENG [0 to 200 / 120 / 1 deg/step]

    109 M-thick:FC:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
    110 M-thick:FC:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]
    111 M-thick:BW:Center:Low Speed *ENG [100 to 180 / 143 / 1 deg/step]
    112 M-thick:BW:Press:Low Speed *ENG [0 to 200 / 120 / 1 deg/step]
    Hope this helps
    Attached Files Attached Files

  9. #19
    Service Manager 1,000+ Posts
    Join Date
    Jun 2012
    Location
    Turnhout
    Posts
    1,397
    Rep Power
    38

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by mga View Post
    Hope this helps
    SP1-106-1 is a temperature display mode. No adjustment can be made there.


    This T.B. is for MET-C1b, is that c3003?

  10. #20
    Copier Technician 1,000+ Posts
    mpc3003 offset (ghost image) after sleeve unit replaced

    mga's Avatar
    Join Date
    Dec 2010
    Location
    london
    Posts
    1,184
    Rep Power
    114

    Re: mpc3003 offset (ghost image) after sleeve unit replaced

    Quote Originally Posted by Mark Bbb View Post
    SP1-106-1 is a temperature display mode. No adjustment can be made there.


    This T.B. is for MET-C1b, is that c3003?
    Yes covers mpc3003 3503 4503 5503 6003 you need to make sure you you set for mpc3003

    Also do this
    3612-131-132-133-134 K.,C,M&Y
    SET ALL TO 600

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Get the Android App
click or scan for the Copytechnet Mobile App

-= -= -= -= -=


IDrive Remote Backup

Lunarpages Internet Solutions

Advertise on Copytechnet

Your Link Here