Konica Minolta C360i

Collapse
X
Collapse
 
  • Page of 4
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 template Next
  • Albonline
    Service Manager

    1,000+ Posts
    • Sep 2008
    • 1144
    #46
    Re: Konica Minolta C360i

    depends on randomizing the read write areas, IE don't keep using the same memory addresses over and over. the m2 series ssd's incorporate randomizing technology.

      Comment

      • copier tech
        Field Supervisor

        5,000+ Posts
        • Jan 2014
        • 8131
        #47
        Re: Konica Minolta C360i

        Originally posted by EarthKmTech
        Note,

        I had this issue on a new machine - the initialized cpu board was required to fix but it is also possible with a secret procedure to initialize the partition table of the ssd. A new ssd was not required. Contact technical support if required - it's not allowed to be shared.
        Would you mind sending this via PM please?
        Let us eat, drink, and be merry, because tomorrow we may die!

        For all your firmware & service manual needs please visit us at:

        www.copierfirmware.co.uk - www.printerfirmware.co.uk
        ​

          Comment

          • tsbservice
            Field tech

            Site Contributor
            5,000+ Posts
            • May 2007
            • 7986
            #48
            Re: Konica Minolta C360i

            Originally posted by copier tech
            Would you mind sending this via PM please?
            Sadly EarthKmTech isn't active member anymore. I hope the best for him he was/is one of the best techs I ever heard of.
            A tree is known by its fruit, a man by his deeds. A good deed is never lost, he who sows courtesy, reaps friendship, and he who plants kindness gathers love.
            Blessed are they who can laugh at themselves, for they shall never cease to be amused.

              Comment

              • femaster
                Service Manager

                1,000+ Posts
                • May 2011
                • 1482
                #49
                Re: Konica Minolta C360i

                Originally posted by copier tech
                Originally posted by EarthKmTech
                Note,

                I had this issue on a new machine - the initialized cpu board was required to fix but it is also possible with a secret procedure to initialize the partition table of the ssd. A new ssd was not required. Contact technical support if required - it's not allowed to be shared.

                Would you mind sending this via PM please?
                One of our techs had to do this about a month ago. He doesn't remember how to get to the point where you can do it any longer, but even if he did remember, it wouldn't help anyway. He stated that the procedure to actually execute the re-partitioning of the SSD is similar to that of recovering from a license error. The copier will provide you with a long code that you must then relay to tech support over the phone and they in turn will then provide you with a corresponding code to enter into the copier to actually execute the partitioning.
                A Ricoh Service Tech for 7 year. A Konica Minolta Service Tech for 7 years. Now, KM service manager for 4 years.
                My Ricoh knowledge is slowly dwindling away at this point. Many things have been lost to time...

                  Comment

                  • copier tech
                    Field Supervisor

                    5,000+ Posts
                    • Jan 2014
                    • 8131
                    #50
                    Re: Konica Minolta C360i

                    Originally posted by femaster
                    One of our techs had to do this about a month ago. He doesn't remember how to get to the point where you can do it any longer, but even if he did remember, it wouldn't help anyway. He stated that the procedure to actually execute the re-partitioning of the SSD is similar to that of recovering from a license error. The copier will provide you with a long code that you must then relay to tech support over the phone and they in turn will then provide you with a corresponding code to enter into the copier to actually execute the partitioning.
                    Ah OK thanks. Don't know why KM make if so difficult to recover some issues. if I'm working on a machine after hours & need to call them I have to return the following morning, painful.
                    Let us eat, drink, and be merry, because tomorrow we may die!

                    For all your firmware & service manual needs please visit us at:

                    www.copierfirmware.co.uk - www.printerfirmware.co.uk
                    ​

                      Comment

                      • uullxx
                        Junior Member
                        • Oct 2014
                        • 5
                        #51
                        Re: Konica Minolta C360i

                        Hi, I have the same problem ...
                        I replaced the STRB and now the machine loads the firmware successfully. But it still doesn't start. It stops at 25%
                        I cannot access the service mode. In a previous post I read about warm boot ... (how do you do it?)
                        Thanks for the replies

                          Comment

                          • Gift
                            Service Manager

                            1,000+ Posts
                            • Mar 2011
                            • 2459
                            #52
                            Re: Konica Minolta C360i

                            Originally posted by uullxx
                            Hi, I have the same problem ...
                            I replaced the STRB and now the machine loads the firmware successfully. But it still doesn't start. It stops at 25%
                            I cannot access the service mode. In a previous post I read about warm boot ... (how do you do it?)
                            Thanks for the replies
                            In same cases you have to let the machine alone for a while like something is happening in the background that can take >30 minutes.
                            Did you used a new STRGB? IIRC in rare cases a faulty CPU board can cause this, too.

                              Comment

                              • uullxx
                                Junior Member
                                • Oct 2014
                                • 5
                                #53
                                Re: Konica Minolta C360i

                                Ok, today I mounted a new CPU board and the machine is working fine.
                                I also tried to install the old STRB but it doesn't work
                                Thanks for the reply

                                  Comment

                                  Previous 1 2 3 4 template Next
                                  Working...