FS-536SD

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • copierlady
    Trusted Tech

    250+ Posts
    • Apr 2008
    • 338
    #1

    FS-536SD

    Hi Guys,
    Setting up a FS 536SD and the tray holder advanced up to far and is hitting the cover. Is there a way to make it go back down before I power up again? I know I have run into this before years ago but I cant remember what to do. I think it happened because the tray was not on when the finisher was setting itself up. Thought about taping down the sensors on the top and restarting. Just wanted some input before I try that.
    Thanks
    Tags: finisher, sensors, setting, tray
    • Synthohol
      Certified Konica Expert

      Site Contributor
      5,000+ Posts
      • Mar 2016
      • 5849
      #2
      Re: FS-536SD

      You gotta open the finisher door, hold up the actuators and close finisher door and the tray will think it's fill and it will lower.
      The other was is remove rear cover and depress the spring clutch gear so it Lowers the tray, that should be done with machine off .
      We know a thing or two because we've seen a thing or two.
      The medication helps though...

        Comment

        • copyman
          Owner / Technician

          Site Contributor
          2,500+ Posts
          • Sep 2005
          • 4723
          #3
          Re: FS-536SD

          I just remove the rear cover and turn the pulley that lowers & lifts the belt for tray

            Comment

            • copierlady
              Trusted Tech

              250+ Posts
              • Apr 2008
              • 338
              #4
              Re: FS-536SD

              Originally posted by Synthohol
              You gotta open the finisher door, hold up the actuators and close finisher door and the tray will think it's fill and it will lower.
              The other was is remove rear cover and depress the spring clutch gear so it Lowers the tray, that should be done with machine off .
              Thank you. I will give it a shot.

                Comment

                • copierlady
                  Trusted Tech

                  250+ Posts
                  • Apr 2008
                  • 338
                  #5
                  Re: FS-536SD

                  Originally posted by copyman
                  I just remove the rear cover and turn the pulley that lowers & lifts the belt for tray
                  OK Got it. Thank you.

                    Comment

                    • blackcat4866
                      Master Of The Obvious

                      Site Contributor
                      10,000+ Posts
                      • Jul 2007
                      • 23009
                      #6
                      Re: FS-536SD

                      Originally posted by copyman
                      I just remove the rear cover and turn the pulley that lowers & lifts the belt for tray
                      This is the way I would have told you.

                      Originally posted by Synthohol
                      You gotta open the finisher door, hold up the actuators and close finisher door and the tray will think it's fill and it will lower.
                      The other was is remove rear cover and depress the spring clutch gear so it Lowers the tray, that should be done with machine off .
                      I used to use this one when shipping out finishers for delivery. It has to be lowered some to unscrew the tray. Our delivery guys were not always very delicate with the finishers (I don't mean you, Thayer). =^..^=
                      If you'd like a serious answer to your request:
                      1) demonstrate that you've read the manual
                      2) demonstrate that you made some attempt to fix it.
                      3) if you're going to ask about jams include the jam code.
                      4) if you're going to ask about an error code include the error code.
                      5) You are the person onsite. Only you can make observations.

                      blackcat: Master Of The Obvious =^..^=

                        Comment

                        • elmaligno
                          Expert technician KM

                          250+ Posts
                          • Oct 2009
                          • 302
                          #7
                          Re: FS-536SD

                          Originally posted by copierlady
                          Hi Guys,
                          Setting up a FS 536SD and the tray holder advanced up to far and is hitting the cover. Is there a way to make it go back down before I power up again? I know I have run into this before years ago but I cant remember what to do. I think it happened because the tray was not on when the finisher was setting itself up. Thought about taping down the sensors on the top and restarting. Just wanted some input before I try that.
                          Thanks
                          You can do it too in service mode,finisher settings, test , main tray up/down
                          Field technician since 1994

                            Comment

                            • Synthohol
                              Certified Konica Expert

                              Site Contributor
                              5,000+ Posts
                              • Mar 2016
                              • 5849
                              #8
                              Re: FS-536SD

                              When the upper limit switch is activated I have never had a response in service mode for lowering the tray, the error code usually cancels the ability.
                              Ymmv good luck
                              We know a thing or two because we've seen a thing or two.
                              The medication helps though...

                                Comment

                                Previous template Next
                                Working...