[Misc] TA 4002i has a continuously running exit unit until it goes into sleep mode

[KCJeff]

I had a customer just call about their TA 4002i's exit rollers running until the machine goes into sleep mode. Anyone have this issue? Since it's the end of my day I thought I would throw this out and check back in tomorrow before I have to call the dreaded Tech Support.

Thanks for your help!

[KYO_OEM]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Set U346/ "Fuser Power Mode " to "OFF" or went into System Menue/ Adjustment_Maintenance/ activate "Silent Mode"
Take care for attached addidtional informations

[KCJeff]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Set U346/ "Fuser Power Mode " to "OFF" or went into System Menue/ Adjustment_Maintenance/ activate "Silent Mode"
Take care for attached addidtional informations

Thanks for the info, will give it a try. I also changed the sleep and low power timers, they were set way to high.

[Samanator]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Part of my set up for new and used machines is to set U346/ "Fuser Power Mode " to "OFF".

I found out about setting U346 Fuser Power Mode on this forum about maybe 18 months ago and have implemented that change in all my xxx2s and xxx3s.

To this date, I have a LOT fewer fuser failures than before.

I also do it to the xxx4 series machines I get.

[BillyCarpenter]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Part of my set up for new and used machines is to set U346/ "Fuser Power Mode " to "OFF".

I found out about setting U346 Fuser Power Mode on this forum about maybe 18 months ago and have implemented that change in all my xxx2s and xxx3s.

To this date, I have a LOT fewer fuser failures than before.

I also do it to the xxx4 series machines I get.

That's good enough for me. Now it'll be part of my routine. Thanks.

[tmaged]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

I've also started disabling IPV6 on all machines, since it's caused some Issues. I also turn all U287 to on.

[kuby]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

I've also started disabling IPV6 on all machines, since it's caused some Issues. I also turn all U287 to on.

Yes Kyocera recommends disabling IPV6 also.

[JR2ALTA]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

So what's the difference between "Fuser Power" and just plain "Silent Mode"? I've been using Silent Mode with good results, I never thought to look at Fuser Power.

[tmaged]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

We've tried silent mode, but it slows the machine down so much that customers complain. I believe it controls fans and other things also.
Fuser power just keeps the fuser from continually running.

[Samanator]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

I've also started disabling IPV6 on all machines, since it's caused some Issues. I also turn all U287 to on.

I understand turning off IPV6, I have been doing that from the time it has showed up on the machines.

What is the advantage of turning on all U287?

[tmaged]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

I understand turning off IPV6, I have been doing that from the time it has showed up on the machines.

What is the advantage of turning on all U287?

All the C & CF codes, with the excpetion of the fuser related C6xxx codes, will try to reset themselves.

[pascalb.]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Hello,
just for info, I found the BT of the TA 4056i which corresponds to the 4002i at Kyo.
For noises at the ejection, I had often a few years ago

noise.pdf

[Paulm]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Just put it in silent mode under maintenance and adjustments in system settings.

[darry1322]

Re: TA 4002i has a continuously running exit unit until it goes into sleep mode

Just put it in silent mode under maintenance and adjustments in system settings.

Thanks for posting but about half this thread is a discussion of Silent Mode. The first suggestion included Silent Mode.