SC530-18 Functional Problem MP9003

[Toner Boy]

Issue with Tray 3 feed unit, just stalls every 10 pages or so. Swapped with tray 2 feed unit, and they both work (for now....).
Tray 2 will also become useless until machine is rebooted, but only 3rd tray indicated 'out of service'.
Anyone have a definitive code description for this? Only have -2 series and this subcode is nowhere to be found. Assuming feed unit motor, or connector issue.

[Lagonda]

Re: SC530-18 Functional Problem MP9003

Issue with Tray 3 feed unit, just stalls every 10 pages or so. Swapped with tray 2 feed unit, and they both work (for now....).
Tray 2 will also become useless until machine is rebooted, but only 3rd tray indicated 'out of service'.
Anyone have a definitive code description for this? Only have -2 series and this subcode is nowhere to be found. Assuming feed unit motor, or connector issue.

Looks like you may have to contact Ricoh over this one. My version of the Service Manual only goes as far as SC530-16 and I can't find a RTB referring to that SC either.

SC530-01 to 16 refer to cooling fan problems so that may give you somewhere to start.

[anothertech]

Re: SC530-18 Functional Problem MP9003

Paper feed unit fan 3 error
		After the fan turns on, the fan lock signal is checked at 1 sec. intervals. Due to an obstruction or other problem, the lock signal went HIGH 1.5 s after the fan turned on and remained HIGH for 6 consecutive counts. The lock signal should remain LOW during normal operation. The fan stopped and then the machine stopped.
Fan motor overload due to an obstruction. Fan motor connector, harness loose, broken, defective. Fan motor defective.
Inspect the area around the fan for obstructions that could interfere with the rotation of the fan blades. Inspect harness, connector and replace if damaged. Replace PFU fan 3.

[Toner Boy]

Re: SC530-18 Functional Problem MP9003

Nice - thank you guys. Machine only has 50K on it, so I'm expecting it was a connector issue and not defective fan.
Will update if returns.

[borisinho]

Re: SC530-18 Functional Problem MP9003

Hello, I have an MP 7503 machine with the code SC 530 19. There is no error code in the manual and it says that it is specified in a technical bulletin. Does anyone have that bulletin please?

[Saturn]

Re: SC530-18 Functional Problem MP9003

Hello, I have an MP 7503 machine with the code SC 530 19. There is no error code in the manual and it says that it is specified in a technical bulletin. Does anyone have that bulletin please?

It's Bulletin RD223042

SC530-19 Paper feed unit fan 4 error
Note: The machines of this series have four trays in Japan, and machines in areas outside Japan have three trays.
Tray 1 is a tandem tray, but Tray 1 in Japan is smaller.
After the fan turns on, the fan lock signal is checked at 1 sec. intervals.
Due to an obstruction or other problem, the lock signal went HIGH 1.5 s after the fan turned on and remained HIGH for 6 consecutive counts.

- The lock signal should remain LOW during normal operation.
- The fan stopped and then the machine stopped.
- Fan motor overload due to an obstruction.
- Fan motor connector, harness loose, broken, defective.
- Fan motor defective.
- Inspect the area around the fan for obstructions that could interfere with the rotation of the fan blades.
- Inspect harness, connector and replace if damaged.
- Replace PFU fan 4.

[luca72]

Re: SC530-18 Functional Problem MP9003

Issue with Tray 3 feed unit, just stalls every 10 pages or so. Swapped with tray 2 feed unit, and they both work (for now....).
Tray 2 will also become useless until machine is rebooted, but only 3rd tray indicated 'out of service'.
Anyone have a definitive code description for this? Only have -2 series and this subcode is nowhere to be found. Assuming feed unit motor, or connector issue.

perhaps when you tear down the pick up station, you left a connector unplugged behind the vertical plastic cover, perhaps a tangle was hidden, and you didn't see it

[Gokhanuvez]

Hello everyone, I have a MP 7503 machine with the code
SC 530 - 17 There is no error code in the manual and it says that it is specified in a technical bulletin. Does anyone have that bulletin please🙏🏻

[luca72]

Hello everyone, I have a MP 7503 machine with the code
SC 530 - 17 There is no error code in the manual and it says that it is specified in a technical bulletin. Does anyone have that bulletin please🙏🏻

I checked, it's not actually in the manual (it stops at 530-16), however, it's probably some fan

check the pin 9 connector for all 3 fans was disconnected behind the waste toner bottle, and the front connector of the pick up stations behind the vertical plastic cover in front of the machine (x3 screw)

did you do any work before the code came out?

[semi]

SC530-17

PFU fan 1 error

Paper feed unit 1 Fan error RTB No.: RD223042

[luca72]

SC530-17

PFU fan 1 error

Paper feed unit 1 Fan error RTB No.: RD223042

great, now I found it too, to search on octopus RTB of the IM7000...you have to go to the MP6503 or previous models (there are quite a few)
compliments to ricoh..LOL

[Gokhanuvez]

Issue with Tray 3 feed unit, just stalls every 10 pages or so. Swapped with tray 2 feed unit, and they both work (for now....).
Tray 2 will also become useless until machine is rebooted, but only 3rd tray indicated 'out of service'.
Anyone have a definitive code description for this? Only have -2 series and this subcode is nowhere to be found. Assuming feed unit motor, or connector issue.

SC 530-17 / 18 The fan blade of the feed unit had come off its shaft. When I pressed it with my finger, it clicked into place and the device started working.

[luca72]

SC 530-17 / 18 The fan blade of the feed unit had come off its shaft. When I pressed it with my finger, it clicked into place and the device started working.

thanks for the feedback, everyone should do this.